background image

 

PLANET TECHNOLOGY CORPORATION 

e-mail: [email protected]   http://www.planet.com.tw 

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528

 

EC Declaration of Conformity

 

 
 
For the following equipment: 
 
*Type of Product

     

:  

300Mbps Dual Band 802.11n Wireless Gigabit Router 

*Model Number  

:  

WDRT-730

 

 
* Produced by: 
Manufacturer’s Name  :  

Planet Technology Corp. 

Manufacturer’s Address:      10F., No.96, Minquan Rd., Xindian Dist., 
 

New Taipei City 231, Taiwan (R.O.C.) 

 
is herewith confirmed to comply with the requirements set out in the Council Directive on the 
Approximation of the Laws of the Member States relating to 

1999/5/EC R&TTE.

 For the 

evaluation regarding the R&TTE the following standards were applied: 
 
 
 

 
EN 300 328 V1.7.1 

(2006-10) 

EN 301 893 V1.5.1           

   

(2008-12) 

EN 301 489-1 V1.8.1 

(2008

-04

EN 301 489-17 V2.1.1 

(2009

-05

EN 62311                    (2008) 

              EN 60950-1                   (2006+A11:2009+A1:2010+A12:2011) 
 
 

Responsible for marking this declaration if the: 

 

Manufacturer 

 Authorized representative established within the EU 

Authorized representative established within the EU (if applicable): 

Company Name:   

Planet Technology Corp. 

Company Address: 

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan 

(R.O.C.)

 

Person responsible for making this declaration 

Name, Surname     

Kent Kang 

Position / Title :   

Product Manager 

 

 

 Taiwan     

 2

th

 July, 2012   

  Place 

Date 

Legal Signature 

Summary of Contents for WDRT-730










































































































Reviews: