Planet Networking & Communication VGW-800FO User Manual Download Page 65

Page: 65 / 76

8-Port SIP Internet Telephony Gateway

VGW-800 Series

Item

Explanation

Trunk ID

SIP trunk ID 1-24

Register Type

Whether this account needs to register or not

Register:

When it is set to register, VGW-800 Series

sends REGISTER message to SIP proxy server for

registration.

Predefine:

When it is set to predefine, VGW-800 Series

DOES NOT send REGISTERED message out.

Domain

The SIP domain for register or call making

Proxy Server

SIP registrar server address

Proxy Server Port

SIP registrar server port number

Outbound Proxy Server

Outbound proxy server address

Outbound Proxy Server

Port

Outbound proxy server port number

Register Expiry

The default register expired for negotiation

Tel No

The registrar telephone number

User ID

The SIP user ID for register and call making

User Password

The SIP password for register and call making

Display Name

The SIP display name

Reject Anonymous Call

Reject the anonymous call

Outgoing Caller ID

The outgoing SIP caller ID mode.

Display Name:

The display name will be set as follows:

None:

No display name will be used

PSTN caller ID:

The display name will be the collected PSTN

caller ID

SIP display name:

The display name will be the Display Name

set in this SIP trunk.

FXO Tel No:

The display name will be the incoming FXO’s Tel

No. set on FXO lines.

User ID:

The SIP caller ID will be used as follows:

SIP user ID:

If the SIP user ID is set, the SIP user ID set

in this SIP trunk will be used and the domain/SIP proxy will be

the host part. The SIP from header’s URL will be the

SIP_User_ID@Domain

SIP_User_ID@SIP_Proxy_Server

PSTN caller ID:

If the PSTN caller ID will be used in

SIP URL, the SIP from header’s URL will be

Summary of Contents for VGW-800FO













































































Search results

Summary of Contents for VGW-800FO

Reviews:

Related manuals for VGW-800FO

Brands by name

Popular brands

Planet Networking & Communication VGW-800FO, User Manual

Search results

Summary of Contents for VGW-800FO

Reviews:

Related manuals for VGW-800FO

Brands by name

Popular brands