Planet Networking & Communication ICA-601 User Manual Download

Page: 59 / 87

3. Disable Motion Detection function.

4. Select “

Firmware name

”

5. Select the Firmware binary file. (

Note

that

it must make sure that

the Firmware only applies to this device, once update, it will be
burned into FLASH ROM of system.

)

6. Once the firmware file was selected, select “Upgrade”.

7. The upgrade progress information will be displayed on

the screen.

8. A message will be shown while the firmware upgraded.

Once the upgrading process completed, the device will
reboot the system automatically.

9. Please wait for 80 seconds, and then you can use IP Wizard to

search the device again.

Warning!!!

The download firmware procedure cannot be interrupted. If the power and/or

network connection are broken during the download procedure, it might possibly cause
serious damage to the device.

Please be aware that you should not turn off the power during updating the firmware and
wait for finish message.

Furthermore, do not try to upgrade new firmware if it’s not necessary.

System Restart

The device is restarted without changing any of the settings.

Summary of Contents for ICA-601
























































































Search results

Summary of Contents for ICA-601

Reviews:

Related manuals for ICA-601

Brands by name

Popular brands

Planet Networking & Communication ICA-601, User Manual

Search results

Summary of Contents for ICA-601

Reviews:

Related manuals for ICA-601

Brands by name

Popular brands