background image

                                                                    Full HD PoE/ Wireless Cube IP Camera 

                                                                                                                                              ICA-1200/W1200

 

 

51

 

 

SMTP Notification (e-mail) 

If enable this function, then the “Send to“ and “Subject” field 

need to be filled. 

Send To 

Type the receiver’s e-mail address. This address is used for 

reply mail. 

Subject 

Type the subject/title of the E-mail. 

TCP Notification 

If enable this function, then the “TCP Server“, “TCP Port”, 

and “Message” fields need to be filled. 

TCP Server 

Type the server name or the IP address of the TCP server. 

TCP Port 

Set port number of TCP server. 

Message 

The message will be sent to FTP server. 

HTTP Notification 

If enable this function, then the fields below need to be filled.

URL 

Type the server name or the IP address of the HTTP server 

HTTP Login name 

Type the user name for the HTTP server. 

HTTP Login Password 

Type the password for the HTTP server. 

Proxy Address 

Type the server name or the IP address of the HTTP Proxy. 

Proxy Port 

Set port number of Proxy. 

Summary of Contents for ICA-1200





























































































Reviews: