WARNING
Take care to remove any dust during the drilling and make sure not to damage any existing cabling
5.4.0 Remove cover from the wall mount (ref Fig 2)
1
, feed mains cable through the larger bottom hole
2
, place correct wall mount into
position and attach to wall using appropriate fi xture devices
3
5.5.0 Electrical Connections
5.5.1 Connect mains cable to appropriate locations on terminal block (ref Fig 2)
4
5.5.2 Connect the Earth (yellow/Green) cable to the Earth Lug (ref Fig 2)
5
WARNING
Replace cover ensuring the cables do not get caught/pinched and attach with the screws located at the bottom and top
6
(ref Fig 3)
5.5.3 Remove dome nut
7
top cover
8
end cap
9
(ref Fig 3)
5.5.4 Slide (push) cable from the light head through tube and out the top
10
, attach swivel with bolt and dome nut and tighten
11
.(ref Fig 3)
When attaching the swivel to the bottom spigot ensure the spigot does not slide up into the tube
5.5.5 Feed cable through grommet
12
and slide into position, trim cable to suitable length
13
5.5.6 Attach to the appropriate locations on the terminal block.
14
(ref Fig 4)
5.5.7 Replace end cap
15
and cover
16
and screw nut
17
down to lock cover in position. (ref Fig 4)
6.0 FINAL INSPECTION, PLEASE ENSURE
6.1.0 The mount is fi rm and has no movement, and is level (ref Fig1)
6.2.0 The light head moves through its full range of movements
6.3.0 The assembly of light and mount is clean and free of any marks
6.4.0 Energise circuit and test the light fi xture for normal operation, that is the green led on the power supply cover is working
18
and the
switch on the light head is working (ref Fig 10)
- NEGA TIVE
BL ACK
+ POSITIVE
RED
6
11
14
15
16
18
17
11
6
6
7
8
13
9
10
12
10
Fig: 3
Fig: 4
WARNING
Only appropriately qualifi ed personnel should carry out maintenance on Planet light fi xtures
9.0 MAINTENANCE:
Planet Lighting recommend that if there is a technical fault with one of our ULED lights, the product is returned to our factory to be
repaired. If a qualifi ed technician is available to repair the fi xture, circuit diagrams, parts lists, and descriptions will be made available
to assist in this process.
The following maintenance procedures performed as required should ensure your Planet Model ULED provides many years of
effective
service
9.1
Cleaning
Carefully remove any loose deposits with a damp sponge. Use a soft brush (non abrasive) or cloth, and/or a mild household detergent
solution to remove dust and other deposits. Do not use steel wool, scrapers, scouring liquids or powders to remove deposits as these
permanently scratch the coating surface. Wipe with clean damp sponge to remove detergent.
9.2
Head Removal (refer Fig 10)
In the unlikely event that one or more of the LED’s should fail, the light head has been designed to be removed without tools for
return to Planet lighting for prompt service. Our LED light head does not contain user seviceable parts.
9.3
Lubrication (refer Fig 9)
To prevent undue stiffness or joint seizure the springs of the Planet Model U have been pre-packed with high quality grease.
The pivoting mechanisms at the main elbow joint and the link pin at the swivel head should receive regular light oiling.
9.4
Lock Nut Adjustment (refer Fig 9)
Fine adjustment of the frictional inertia of the lamp movement is provided by tensioning the small lock nut on the link pin at the base
of the swivel head. This nut should be tensioned so that the lamp fi rmly retains its position when adjusted but can be freely re-
positioned under the pressure of one fi nger at the elbow joint. Do not attempt to correct an unbalanced movement by over-tightening
this nut. (refer Fig 9)
WARNING
UNDER NO CIRCUMSTANCES SHOULD THE SPRING TENSION NUTS (TWO) BE COMPLETELY UNDONE .
(refer Fig 11)
9.5
Spring Tensioning (refer Fig 11)
After extended use the main balance springs of the Model ULED arm may require tension adjustment (generally the spring on your
left hand side when facing the lamp).
This may be done by carefully prising the plastic cap off the end of the spring tube to permit access to tensioning nuts. Nuts should
be tightened in small increments using a 15mm hexagon tube spanner until the lamp assumes correct balance.
Do not over tighten tension springs.
UDP
shown
Universal joint
left hand
(heavy) spring
tube
link pin at the
swivel head
main elbow joint
Fig: 9