Planar PU-16 Manual Download Page 2

  Introduction

 

This  manual  is  part  of  documentation  for  PLANAR  air  heaters  and  provides 

information on safe maintenance of the product. 

 

If you have any problems, we strongly recommend that you contact authorized service 

centers, addresses and telephone numbers of which you can find out from the company, the 
seller or on the website www.autoterm.ru. 

 

 

Before using, the heater please read these instructions and the 
Operation Manual of the Heater. 

 

  Warranty

 

The  manufacturer  is  not  liable  for  defects  and  damages  that  result  from  non-

compliance with the instructions on installation and maintenance of the heater, as well as 
the instructions contained in this manual. 

 

  The Controller shall be used only for heater control. 

  Do  NOT  connect  or  disconnect  the  connector  of  the  Controller  during  the  heater 

operation. 

  After turning off the heater, reconnection should be made at least after 5-10 seconds. 

  For  safe  operation  of  the  heater,  after  two  consecutive  failed  start-ups  customer 

service should be contacted to identify and repair the malfunction. 

 

The warranty period and conditions of the warranty service are listed on the warranty 

card. 

 

  Safety

 

Risk  of  explosion  in  places  where  large  quantities  of  flammable  vapours  and 

gases or large amounts of dust can be generated or accumulated (e.g., gas stations, 
oil depots, warehouses, fuel, coal, wood or grain storage facilities).

 

-  Do NOT start or use the heater 

Risk of poisoning or choking by exhaust gases indoors.

 

-  Do NOT start or use the heater 

Fire hazard due to the presence of flammable materials and fluids in the exhaust gas 
stream.

 

-  Do not allow the presence of combustible materials in the exhaust stream  

Risk of injury due to the use of a defective unit

 

-  Do not use a faulty heater 
-  Contact a service cente

 

 

 

Summary of Contents for PU-16











Reviews: