Planar 2D-12 Installation Instructions Manual Download Page 28 | Manualshive

Page: 28 / 36

background image

28

3.9.6 Heater Electrical Wiring Installation.

Installation of wire harnesses and other electrical parts of

the heater should be made according to the wiring diagram.
Install the harnesses so as to prevent their heating, deformation,
and movement during vehicle operation. Fix the harness with
plastic collars to vehicle parts.

Attention! Mounting shall be carried out with the fuse

removed.

If the length of the fuel pump wiring harness needs
to be shortened, it is allowed to remove an
unnecessary portion from the middle of the
harness. The splice should be insulated.

Installation of the fuel pump electrical harness connector is

shown in Fig.31.

«
...
26
27
28
29
30
...
»

Summary of Contents for 2D-12





































Reviews:

No comments

Related manuals for 2D-12

Brand: Taurus Alpatec Pages: 52

WFC-03 HCM RF 230

Brand: Watts Pages: 11

Aerco AM Series

Brand: Watts Pages: 7

Brand: EnGenius Pages: 2

Brand: Jata Pages: 32

Brand: Optimum Pages: 11

Brand: Toyostove Pages: 2

Powerflex PDVG-40T42

Brand: American Water Heater Pages: 4

Brand: A.O. Smith Pages: 32

Brand: Elpro Technologies Pages: 2

Brand: Pro-Elec Pages: 4

Brand: Rinnai Pages: 32

Brand: Galletti Pages: 32

Brand: IPEX Pages: 27

Flame Guard Safety System

Brand: American Water Heater Pages: 29

Brand: EOS Pages: 48

Brand: Cadet Pages: 2

Brand: SHX Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands