PKP DS02.1 Instruction Manual Download Page 20 | Manualshive

Page: 20 / 20

background image

Accessories (see separate data sheets):

•

Needle valves SNV01, SNV02

•

Ball valves SKG01, SKG02

•

Dirt traps SF00, SF01

•

Protection relay MSR01

•

M12 Plug connector PVC-cable SM12

Notes:

The specified measuring/switching ranges apply when the
instrument is installed vertically and the flow rate is from bottom
to top.
Other installation positions or operating densities deviating from
the specified specifications increase the specified measuring
error.

Special scales for different media and operating conditions are
available on request.

The specified switching points are shut-off points at falling flow
rates. Please note that the switch-on points are higher due to
the hysteresis.

For applications where pressure surges are to be expected,
please contact PKP!

PKP Prozessmesstechnik GmbH

Borsigstr. 24 • D-65205 Wiesbaden

S

+49 (0) 6122-7055-0 •

T

+49 (0) 6122 7055-50

[email protected] • www.pkp.de

«
...
18
19
20

Summary of Contents for DS02.1





















Reviews:

No comments

Related manuals for DS02.1

Brand: Major tech Pages: 8

Brand: Waltron Pages: 25

Brand: Oceanic Pages: 17

Brand: Hammond Pages: 130

Brand: Tascam Pages: 4

Brand: Harpers Pages: 8

Brand: jenway Pages: 50

Brand: jenway Pages: 62

Brand: PASCO Pages: 3

Brand: ACE INSTRUMENTS Pages: 6

Brand: Keller Pages: 8

PHYSICS line C.A 832

Brand: Chauvin Arnoux Pages: 43

Brand: Xylem Pages: 39

truflo TC Series

Brand: ICON Pages: 6

quartz3 BPR zero

Brand: RBR Pages: 22

Brand: AquaMetrix Pages: 37

STARGAS 898 LIGHT

Brand: tecnotest Pages: 146

IPA CONTROL EXACT

Brand: PITSID Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands