Pixsys ATR 142 User Manual Download Page 46

Page: 46 / 58

46 - ATR142 -

User manual

7. s.m.

7 Samples Mean

8. s.m.

8 Samples Mean

9. s.m.

9 Samples Mean

10.s.m.

10 Samples Mean

tune

Tune

tuning type selection

dis.

Disabled >

Default

auto

Automatic. PID parameters are calculated at

each activation and/or change of setpoint.

man.

Manual. Launch by keyboard or by digital input.

once

Once (P.I.D. parameters calculation only at first

start)

s.d.tu.

Setpoint Deviation Tune

select the deviation from the command setpoint

as threshold used by Autotuning to calculate PID

parameters.

0-5000

[digit

], (degrees.tenths for temperature sensors)

Default

: 10.

op.mo.

Operating Mode

select operating mode (parameter 7.11)

cont.

Controller >

Default

pr.cY.

Programmed Cycle

2t.s.

2 Thresholds Switch

2t.s.i.

2 Thresholds Switch Impulsive

3t.s.i.

3 Thresholds Switch Impulsive

4t.s.i.

4 Thresholds Switch Impulsive

au.ma.

Automatic/Manual

enable automatic/manual selection. (parameter 7.6)

dis.

Disabled >

Default

en.

Enabled

en.st.

Enabled Stored

Summary of Contents for ATR 142



























































Search results

Summary of Contents for ATR 142

Reviews:

Brands by name

Popular brands

Pixsys ATR 142, User Manual

Search results

Summary of Contents for ATR 142

Reviews:

Brands by name

Popular brands