manualshive.com logo in svg

Pixsys ATR 142, User Manual

Share
Download
Pixsys ATR 142 User Manual Download Page 45

User manual - 

ATR142-  45  

9. s.m.

 

9 Samples Mean

10.s.m.

  10 Samples Mean > 

Default

11.s.m.

 

11 Samples Mean

12.s.m.

 

12 Samples Mean

13.s.m.

 

13 Samples Mean

14.s.m.

  14 Samples Mean

15.s.m.

  15 Samples Mean

44 

c.frn.

 

Conversion Frequency

Frequency of sampling for analogue-digital converter.

242H.

 

242 Hz Max ADC conversion frequency

123H.

 

123 Hz

62 H.

 

62 Hz

50 H.

 

50 Hz

39 H.

 

39 Hz

33.2H.

 

33.2 Hz

19.6H.

 

19.6 Hz

16.7H.

 

16.7 Hz  > 

Default

12.5H.

 

12.5 Hz

10 H.

 

10 Hz

8.33H.

 

8.33 Hz

6.25H.

 

6.25 Hz

4.17H.

 

4.17 Hz Min. ADC conversion frequency

45 

v.fLt.

 

Visualization Filter

slow down the refresh of display in order to simplify 

the reading (keeping unchanged the ADC conversion 

frequency)

dis.

 Disabled

ptcH

 

Pitchfork filter > 

Default

fi.or.

 

First Order

f.or.p.

 

First Order with Pitchfork

2. s.m.

 

2 Samples Mean

3. s.m.

 

3 Samples Mean

4. s.m.

 

4 Samples Mean

5. s.m.

 

5 Samples Mean

6. s.m.

 

6 Samples Mean

Summary of Contents for ATR 142



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands