7
Press the
switch for
6 seconds
UP
DOWN
DOWN
UP
OFF
START
OFF
START
OFF
START
SET
Press
UP
DOWN
(Factory setting: Normal Mode)
Setting Completed
(e.g.)
Blink
1
Setting into SP Mode.
3
2
Degree of Acceleration
(output) 20%
4
5
Press down on pedal.
Switch Mode to SP7
Switch Mode to Ec5
In NORMAL Mode
40
%
Display
(Lock)
(Normal)
Name
Lock
Normal
Safety
Mode
NORMAL Mode.
Status at Engine Restart
About Safety Mode
●
In SPORTS Mode when key is turned OFF
●
In NORMAL or ECO Mode when key is turned OFF
Changes automatically
and starts.
Starts same as
last time.
Starts same as
last time.
Changes Automatically
Changes Automatically
Changes Automatically
Check acceleration during ECO-driving
USE
1
Check control status
USE
3
Check acceleration during regular driving
USE
2
0
%
10
100
%
0
%
100
%
Mode Settings for when Restarting the Engine
[Safety Start Settings]
Degree of Acceleration Monitor
Main Unit Display Area
Operational Procedure
Select from 3 modes in which to start the engine: “Same as Last”
Mode, “Normal” Mode or “Safety” Mode.
Change Ratios and Modes when Key is
turned OFF.
When the key is turned OFF and
SPORTS Mode had been set at SP4 or
higher it will automatically change to SP3.
If the change ratio for SPORTS Mode has been set at SP4 or
higher, when the key is turned OFF, to improve safety the ratio will
be changed to SP3 when the engine is restarted.
The change ratio in SPORTS Mode will automatically changed
from SP4 or higher to SP3 even if when the key is turned OFF the
unit is in NORMAL Mode or ECO Mode.
After “iGn” has flashed for 3
seconds the current setting
will be displayed.
Press down on the
SET Switch for at
least 6 seconds.
Safety
Mode
If no operation is
carried out for 5
seconds, the display
returns to show the
mode.
The mode will
change with each
pressing of the
UP/DOWN switch.
Displays the amount of pressure placed on the accelerator pedal. (output signal)
[10 - 100%, 1% unit]
To e n s u r e r e d u c e d f u e l
c o n s u m p t i o n d u r i n g
acceleration the degree of
a c c e l e r a t i o n s h o u l d b e
between 15% and 25%. To
further improve results use
ECO Mode when wishing to
save fuel.
With the key in the ON (engine not
running) position and under NORMAL
Mode press in the pedal until it reaches
40% (A40), if the Mode is changed to
SP7 the display should read 67% (A67)
and if placed in Ec5 the display should
change to 20% (A20).
[
⇒
Refer to the Graph of “Basic Control
Features” on Page 6]
※
The actual display may differ slightly.
Please use to check the degree of acceleration for any type of
driving, not just ECO Mode.
●
Degree of Acceleration Monitor shows the rate of acceleration output to the ECU where 0 repre-
sents the pedal not being pressed in and 100 equals when the pedal is fully pressed down.
●
The display will show when degree is above 10%.
※
When in ECO Mode, even if the accelerator is stepped on a full 100% the output signal will only
be 80%.
Depending on characteristics of the accelerator or on how the accelerator is stepped on the
display may only read up to 79%.
※
In both Normal Mode and Sports Mode the display may only read up to 99%.
e
.g.
40
%
Bef
o
re
Using
F
eatures
Connecting
The Wires
Installing
The Product
Ho
w to
Operate
T
roub
le-
Shooting
Initial
Settings
ECO
＝
-
