4
PIVOT CORPORATION
87-3, Shimookada Okada, Matsumoto-shi, Nagano, 390-0313 Japan TEL0263-46-5901
1
0
OFF
OFF
ON
Engeine
Start
Basic Flow of Operations
Troubleshooting
The Opening Demo does not work.
Poor connection or wrong wiring of each cable.
Please reconfirm whether wiring and connections are correct or not.
Poor connection of
White
wire.
Please reconfirm whether wiring and connections are correct or not.
The shift lamp does not light up.
The cylinder setting is wrong.
The signal detection level is not correct.
See page 3 [SETTING F] and [Wiring Chart], make any necessary changes.
Check the
Orange
wire connections or conditions.
The shift lamp brightness setting is set too low.
See page 3 [SETTING E], please check the setting.
The signal detection level is not correct.
See page 3 [SETTING F] and [Wiring Chart], make any necessary changes.
2
1
2
1
Opening
Demo
Opening
Demo
Opening Demo works but the needle
does not work with Engine start.
The car’s tachometer and CSG reading
are very different.
E v e n w i t h t h e p a r k i n g l i g h t s o n ,
brightness of the shift lamp does not
decrease.
The engine rpm has not reached the set shift
point.
Poor connection of
Orange
wire.
See page 3 [SETTING A] and make any necessary changes.
The auto-power window function and/or
other electronic devices are re-set.
Basic Operation
1
2
3
4
5
6
Start the engine.
Engine stop
Meter OFF
Note: Due to characteristics of the gauge, even
though the engine is off and the gauge is not
measuring, the needle will not return to “0” .
Basic Flow of Operations for CSG. For details about settings see page 3 [Settings].
Press the switch
Long press of switch
Changes automatically
Operate switch
No operation
While holding down the
switch, start the engine
Press the switch
for 1.5 seconds
Press the switch
for 3 seconds
Press the
switch
ENGINE START
With no operation
for 5 seconds
Opening Demo
Opening Demo
Shift Point display
Engine Rotation display (Chronometric / Real-time)
Cylinder Number
setting
Peak display
and Re-set
Switch display
Chronometric / Real-time
Shift Point
Setting
Shift Lamp
Brightness setting
With engines stopped
B
SETTING
C
SETTING
E
SETTING
A
SETTING
D
SETTING
Demo-mode setting
Demo-mode setting and deletion
Demo-mode is used in stores to show and explain operations; for most users it is not necessary.
Demo
Operations
Press the
switch for
5 seconds
Demo-mode deletion
Demo-mode
deletion
(Meter light Off)
The lamps blink red 5 times
The needle will show
“1” or “2”
Press the
switch for
10 seconds
• Our products have already been recognized as our Industrial Property or are in the process of receiving Industrial Property status.
• We plan in the near future to take all possible legal measures to protect against unfair competition from look-alike products using similar designs, regulating
characteristics, circuitry and circuitry layout.
• We strictly prohibit the unlicensed use of the PIVOT trademark and the unauthorized use of PIVOT User’ s Manual.
Trouble
Possible Causes
Possible Solutions
This is due to the minus terminal on the battery
being disconnected.
Basic operation from engine start to stopping.
Opening Demo
Current RPM
display
The needle will show
the set shift point
Keep pressing the switch
The ignition OFF
(Meter light Off)
Press the
switch
Press the switch with the
ignition in the OFF position
(meter light off).
Hold down the switch
during Demo Operations
See page 3 [SETTING D] and make any necessary changes in the rpm
shift point.
Re-connect the minus terminal and follow re-setting instructions of
each vehicle manual for any affected devices.
(Note)
Turn the
ignition to
the ON
position
(engine not
running)
