2
ー
1
2
3
Installing The Product
Connecting The Wires
Basic Wiring
: Cut Connector
IGN
(12V with key switch ON)
(See Note on the right)
TA
Earth
Note:
⇒
See
[Reference 1] How to use the Cut
Connectors
on Page 2.
(1.5 m)
(1.5 m)
(1.5 m)
Can be mounted in
various places
Mount almost anywhere
using the double -sided
tape. After mounting it is
possible to for easy-read-
ing.
Note: If you wish to open holes
to fasten the unit to the pillar or
column cover, please purchase
and use the separately sold pillar
holder.
Meter
Dimensions
(unit; mm)
Note: Please be sure about where you
wish to install the meter, as it is not
advisable to reuse double-sided tape.
A. Installation with the Adjustable Stand
B. Mount into the Panel
Slightly loosen the Hex-
agonal bolt and install the
gauge into the Adjustable
Stand.
Fasten using the double-sided
t a p e . (C l e a n t h e s u r f a c e;
removing all oil and dust.)
A f t e r d e c i d i n g t h e
position and angle of the
meter fac e, fasten the
Hexagonal bolt on both
sides to secure.
Fasten using the double-sided tape. (On top of the steering column cover or dashboard.)
Wrap the cushion tape around the base
of the meter.
1
Press into the 80 mm hole in the panel.
2
Orange
Orange
1
10 mm
2
10 mm
3
4
5
Panel
Cushion
tape
Pillar holder for ø80
PH-80
On the dashboard
On the steering
column cover
On the steering
column cover
Pillar
holder
Screw
hole
When another device is already connected
to the RPM signal from the ECU
This wiring is to use the lowest brightness for
the shift lamp when only the parking lights are
on; hence neither the dial or the needle will
be it up when running with parking lights on.
5-pin
connector
Backside
of the Meter
5-pin
connector
Backside
of the Meter
ECU
Engine Computer,
etc.
Cut
connector
White
extension wire
Insulate the cut off
part with tape
Cut the black tube of the wire tip and connect.
White
White
• Painted screws and screws connected to
plastic parts are not earthed; make sure to
connect only to a place which is earthed.
• Make sure to connect the white wire to
indicated place on the car.
Connect to the IGN (12V with key
s w i t c h O N ) u s i n g t h e c u t
connectors(included).
Confirm the positions on the
“ W i r i n g C h a r t ” a n d t h e n
connect the wire using the cut
connectors (included).
Earth
IGN
RPM Signal
Wiring
Chart
Note: When crimping,
please use crimpers or
use pliers to bend and
then solder together.
Peel off of the vinyl
cover at connection.
Peel off of the vinyl
cover at the end of
the product’ s wire.
Wrap around both
wire coils.
Close tightly with cut
connector.
I n s u l a t e w i t h v i n y l
tape.
with earth
terminal
Black
Black
Fasten to a screw of a
m e t a l p a r t w hi c h i s
earthed.
Red
Red
Hexagonal
bolt
Hexagonal
bolt
Adjustable
Stand
Clean to remove
oil and dust
Double-sided
tape (Included)
A pillar
: Use cut connector
▶
and that device works properly keep that wiring.
▶
and the meter or other device stops working properly or sometimes becomes unstable
disconnect from the ECU wire and get the RPM from the minus terminal of ignition coil or
diagnosis.
⇒
See following “To get the RPM signal from other than the ECU”
Location of
the RPM signal
(IG − )
e.g.) in case of
MAZDA EUNOS
ROADSTER (NA6C)
←
To meter
Ignition coil
←
To meter
←
To meter
Set the Cylinder Number setting to “1” .
⇒
See page 3
Connection for Cylinder Number Setting
To get the RPM signal from other than the ECU
Note : Set the Cylinder Number setting to "1". Make sure to
check the wiring position of the ignition signal which will vary
depending on the car models.
White
White
White
Direct Ignition coil
Ignition signal
• To get the RPM signal from diagnosis
(check connector)
• To get the RPM signal from the
ignition coil
• To get the RPM signal from the ignition signal of
the direct ignition coil
If display the extremely
low number of RPM by
above connecting
e.g.) Genuine tachometer of a six-cylinder car
displays the 500rpm at the 3000rpm. The reason
is that the car is independent ignition type.
[Reference
]
How to use the Cut
Connectors
If the
White
wire is not long enough,
please use the white wire
( 1.5 m)
provided
in this package to extend the length.
Parking light
(12V with
parking light
ON)
Dimming Shift Lamp along with parking lights
(Not normally
required)
Install in an easy-to-view location.
ø80
ø92
17.5
23.5
