background image

Page 2

For technical questions, please call 1-888-866-5797.

Item 56368 56371

Specifications

Model

56371

56368

Capacity  
(Evenly distributed across two Stands.)

3 Tons (6,000 lb.)*

6 Tons (12,000 lb.)*

Approximate Height Range

11-3/4" – 16-3/4"

16-1/8" – 23-5/8"

*Evenly distributed across two Jack Stands.

Important Safety Information

Failure to heed these markings may result in  
personal injury and/or property damage:

1. 

Study, understand, and 
follow all instructions before 
operating this device.

2. 

Do not exceed rated capacity.

3. 

Use only on hard, level surfaces.

4. 

Center load on saddle.

5. 

Use as matched pair to support 
one end of a vehicle only.

6. 

Wear ANSI-approved safety goggles 
and heavy-duty work gloves 
during use.

7. 

Do not use for aircraft purposes.

8. 

Support vehicle only at manufacturer-
recommended locations.

9. 

Inspect before every use;  
do not use if parts loose or damaged.   
Do not use if even a minor crack, 
bend or other damage/deformation 
appears. Discard Jack Stand 
if damaged or deformed.

10. 

Keep work area clean

.  

Cluttered areas invite injuries.

11. 

Observe work area conditions

Keep work area well lighted.

12. 

Keep children away

.  Children must 

never be allowed in the work area. 

13. 

Stay alert

.  Watch what you are doing,  

use common sense. Do not operate 
any tool when you are tired.

14.  Do not use to support a 

lawn mower or tractor. 

15.  Do not move or rock a vehicle 

supported by stands.

16.  The warnings, cautions, and instructions 

discussed in this instruction manual 
cannot cover all possible conditions 
and situations that may occur. It must 
be understood by the operator that 
common sense and caution are factors 
which cannot be built into this product, 
but must be supplied by the operator.

Summary of Contents for 56368









Reviews: