background image

UNPACKING AND INSPECTION 

 

Remove the cabinet from shipping carton, ensuring that all packing ma-
terials and protective plastic has been removed from the unit.  Inspect all 
components for completeness and condition. 

If any freight damage is present, a freight claim must be filed immediately 
with the shipping company. 

Freight damage is not covered under warranty

Check to insure all components are included: cabinet, instruction packet 
and additional accessories, such as product dividers. 

Read operation instructions completely. 

Connect power cord to grounded and properly wired electrical source as 
specified. 

Appliance should be thoroughly cleaned before use.  See CLEANING 
INSTRUCTIONS, page seven. 

Refer to 

SHIPPING DAM-

AGE CLAIM PROCEDURE 

on bottom of this page. 

 
 
 
 

FREIGHT DAMAGE PROCEDURE 

NOTE: 

For your protection, please note that equipment in this shipment was carefully inspected and packaged 

by skilled personnel before leaving the factory.  Upon acceptance of this shipment, the transportation company 
assumes full responsibility for its safe delivery. 

 
 

IF SHIPMENT ARRIVES DAMAGED: 

1. 

VISIBLE LOSS OR DAMAGE: 

Be certain that any visible loss or damage is noted on the freight bill or 

express receipt, and that the note of loss or damage is signed by the delivery person. 

2. 

FILE CLAIM FOR DAMAGE IMMEDIATELY: 

Regardless of the extent of damage. 

Contact your dealer 

immediately. 

3. 

CONCEALED DAMAGE:

  If damage is unnoticed until the merchandise is unpacked, notify the transporta-

tion company or carrier immediately, and then file a “CONCEALED DAMAGE” claim with them.  This should 
be done within fifteen (15) days from the date the delivery was made to you. 

Be sure to retain the con-

tainer for inspection

 
 

Pitco cannot assume liability for damage or loss incurred in transit, 

freight damage is not covered under war-

ranty

. We will, however, at your request, supply you with the necessary documents to support your claim. 

 
 
 
 
 
 
 
 
 

4

1. 

 
 
2. 

 
3. 

This appliance 
should be 
thoroughly 

cleaned prior to use. 
 
See the CLEANING 
INSTRUCTIONS, on page 7 
of this manual. 

4.

NOTE: DO NOT 

discard 

5. 

6. 

 

7. 

the carton or other packing 
materials until you have 
inspected the appliance for 
hidden damage and tested 
it for proper operation. 

Summary of Contents for CRISP N' HOLD PCF14











Reviews: