11
10
11. INSTALLING THE FLAME BROILER COMPONENTS
Parts Required:
1 x Flame Broiler Slider (#4)
1 x Flame Broiler Main Plate (#5)
1 x Flame Broiler Adjusting Bar Handle (#12)
1 x Flame Broiler Adjusting Bar (#13)
Installation:
• Insert the flame broiler main plate into the main grill, right side first.
Rest the flame broiler main plate on the built-in ledge (on the inside
right) of the main grill that directs grease towards the grease bucket.
Slide the entire piece to the left side, and the two slots on the flame
broiler main plate will fit into the rounded ledge above the Burn Pot.
It will sit slightly at a downward angle. Note 11A.
IMPORTANT: If the flame broiler main plate is on the base of the
barrel, it is installed incorrectly. The flame broiler main plate should
sit at an angle, with the left side sitting higher than the right. Poor
installation of this part may result in damage to your main grill
barrel.
• Place the flame broiler slider on top of the flame broiler main plate,
covering the slotted openings. Ensure the raised tab is on the left,
to easily adjust for direct or indirect flame when cooking. Note
illustration 11B. Both flame broiler parts are lightly coated with oil to
avoid rusting when shipped.
• Next, remove the flame broiler adjusting bar handle from the flame
broiler adjusting bar. Insert the flame broiler adjusting bar through
the opening hole on the left side of the main barrel. Add the flame
broiler adjusting bar handle back onto the end outside the barrel.
Next, slide the notched end of the adjusting bar into the locking tab
on the flame broiler slider, giving you adjustable access to the flame
broiler slider on the main plate. Note steps in 11C.
NOTE: When the flame broiler slider is open and direct flame is used,
do not leave the grill unattended for any period of time.
Place the flame broiler slider on top of the flame
broiler main plate covering the slotted openings.
Ensure the raised tab is on the left and the two pins
at the bottom of the flame broiler slider place into
the holes of the flame broiler main plate.
to easily
adjust for direct or indirect flame when cooking. Both
flame broiler parts are lightly coated with oil to avoid
rusting when shipped.
Insert the flame broiler adjusting bar
through the opening hole on the left
side of the main barrel. Add the flame
broiler adjusting bar handle on the end
outside the barrel. Next, slide the
notched end of the adjusting bar into
the locking tab on the flame broiler
slider, giving you adjustable access to
the flame broiler slider on the main
plate.
11A
11B
11C
Insert the flame broiler adjusting bar
through the opening hole on the left
side of the main barrel. Add the flame
broiler adjusting bar handle on the end
outside the barrel. Next, slide the
notched end of the adjusting bar into
the locking tab on the flame broiler
slider, giving you adjustable access to
the flame broiler slider on the main
plate.
Insert the flame broiler adjusting bar
through the opening hole on the left
side of the main barrel. Add the flame
broiler adjusting bar handle on the end
outside the barrel. Next, slide the
notched end of the adjusting bar into
the locking tab on the flame broiler
slider, giving you adjustable access to
the flame broiler slider on the main
plate.
Insert the flame broiler adjusting bar
through the opening hole on the left
side of the main barrel. Add the flame
broiler adjusting bar handle on the end
outside the barrel. Next, slide the
notched end of the adjusting bar into
the locking tab on the flame broiler
slider, giving you adjustable access to
the flame broiler slider on the main
plate.
B
B
A
A
5
4
5
12 13
9. INSTALLING THE FRONT SHELF BRACKETS
Parts Required:
1 x Front Shelf Bracket / Left (#17)
1 x Front Shelf Bracket / Right (#18)
6 x Screw (#A)
Installation:
• Attach one front shelf bracket to the front of the grill barrel by using
three screws. Install each screw halfway, then tighten completely
when all three screws are mounted and aligned properly.
• Repeat the same installation for the other front shelf bracket.
10. MOUNTING THE FRONT SHELF
Parts Required:
1 x Front Shelf (#19)
2 x Washer (#B)
2 x Screw (#H)
2 x Nut (#I)
2 x Bushing (#J)
Installation:
• From underneath, insert the screw (from the outside) into the front
shelf bracket and the front shelf, then add the bushing onto the screw,
the washer, then the nut. Repeat installation for the other side of the
front shelf.
NOTE: When installed correctly, the front shelf can be raised (for use)
and lowered (for storage) with ease.
IMPORTANT: Avoid using the shelves to move or lift the grill. The
weight of the unit will cause the shelves to break, which is not
covered by warranty.
9
A
17
18
10
B
J
H
I
19
