9
8
6. ASSEMBLING THE SIDE SHELF
Parts Required:
1 x Side Shelf (#16)
3 x Tool Hook (#D)
Installation:
• Turn the side shelf upside down. On the edge of the side shelf with
three holes, install the tool hooks into each hole along the edge. The
tool hooks will secure to the nut that is pre-mounted on the inside.
7. MOUNTING THE SIDE SHELF
Parts Required:
4 x Screw (#A)
4 x Locking Washer (#C)
4 x Washer (#B)
Installation:
• From underneath, fasten the side shelf to the side panel of the main
barrel using four screws, locking washers, and washers.
NOTE: Do not tighten screws completely until all screws have been
installed. Once all screws are installed, then tighten securely.
IMPORTANT: Avoid using the shelves to move or lift the grill. The
weight of the unit will cause the shelves to break, which is not
covered by warranty.
8. SECURING THE CHIMNEY
Parts Required:
1 x Chimney Cap (#6)
1 x Chimney Stack (#7)
1 x Chimney Gasket (#8)
2 x Screw (#A)
2 x Locking Washer (#C)
2 x Washer (#B)
Installation:
• Locate the chimney opening on the side of the main barrel. From the
outside, secure the chimney and chimney gasket to the side panel
using two screws, locking washers, and washers. The screw will fasten
to the pre-mounted nut on the inside of the barrel.
• Next, secure the chimney cap onto the top of the chimney stack by
rotating the chimney cap screw into the chimney stack.
NOTE: Adjust the chimney cap to affect the airflow inside the main
grill. If cooking at low temperature, keep the cap more open. Ensure
the chimney cap allows for air to escape.
6
16
D
D
D
AX4
BX4
CX4
7
BCA
BCA
BCA
BCA
AX2
BX2
CX2
8
6
7
BCA
BCA
8
2. INSTALLING THE BOTTOM SHELF
Parts Required:
1 x Bottom Shelf (#24)
4 x Screw (#A)
4 x Washer (#B)
4 x Locking Washer (#C)
Installation:
• Mount the Bottom Shelf to each Support Leg using a screw, locking
washer, and washer. Ensure the flat surface of the shelf is facing up
towards the Grill Barrel.
3. ADDING WHEELS TO THE CART
Parts Required:
2 x Locking Caster Wheels (#25)
2 x Wheel (#26)
2 x Wheel Cotter Pin (#E)
2 x Wheel Washer (#F)
2 x Wheel Axle Pin (#G)
Installation:
• Insert each Locking Caster Wheel into the bottom of each Left Support
Leg by hand-tightening into the hole. Ensure that each Locking Caster
Wheel is inserted completely. Note illustration 3A.
• Attach each Wheel to each Right Support Leg by inserting the Wheel
Axle Pin through the Wheel, Support Leg hole, Wheel Washer, then
secure using the Wheel Cotter Pin. Note illustration 3B.
• Once the shelf is secure, carefully lift the grill into an upright position.
IMPORTANT: Re-tighten the support leg screws to ensure they are
completely secure after positioning the grill upright.
4. SECURING THE LID STOPPER
Parts Required:
1 x Lid Stopper (#3)
Installation:
• Secure the Lid Stopper onto the top of the Main Barrel using the
pre-installed screw on top of the Main Barrel.
5. INSTALLING THE LID HANDLE
Parts Required:
2 x Lid Handle Bezel (#10)
1 x Lid Handle (#11)
Installation:
• Remove the pre-installed screws from the Lid Handle. From inside the
barrel lid, insert one screw to protrude to the outside. Add a Lid Handle
Bezel on the screw, then hand-tighten the screw (from the inside) into the
Lid Handle. Repeat the same installation for the other end of Lid Handle.
AX4
BX4
CX4
2
24
AC
B
AC
B
BC
A
BC
A
3A
3B
25
25
26
26
G
G
F
F
E
E
21
20
4
3
5
10
10
11
