Pioneer VSX-933 Instruction Manual Download Page 94

Page: 94 / 131

≫

≫

≫

≫

≫

≫

Miscellaneous

Tuner

Change the frequency step for the tuner.

Setting Item

Default Value

Setting Details

AM/FM

Frequency Step

(North American

models)

10 kHz/0.2 MHz

Select a frequency step to suit your residential

area.

Select "10 kHz/0.2 MHz" or "9 kHz/0.05 MHz".

•

When this setting is changed, all radio presets

are deleted.

AM Frequency

Step (European,

Australian and

Asian models)

9 kHz

Select a frequency step to suit your residential

area.

Select "10 kHz" or "9 kHz".

•

When this setting is changed, all radio presets

are deleted.

Remote ID

Change the remote controller ID.

Setting Item

Default Value

Setting Details

Remote ID

Select an ID for the unit's remote controller from

"1", "2", and "3" to prevent interference between

the unit and other Pioneer components that are

installed in the same room. After changing the ID

on the main unit, change the ID on the remote

controller accordingly with the following procedure.

While pressing and holding the MODE button,

press the following buttons for approx. 3 seconds.

•

To change the remote controller ID to “1”:

(The remote indicator blinks once.)

•

To change the remote controller ID to “2”:

(The remote indicator blinks twice.)

•

To change the remote controller ID to “3”:

(The remote indicator blinks three times.)

Firmware Update

Change the settings for Firmware Update.

Setting Item

Default Value

Setting Details

Update Notice

Enable

Availability of a firmware update is notified via

network.

"Enable": Notify updates

"Disable": Do not notify updates

Version

The current firmware version is displayed.

Update via

NET

Press ENTER to select when updating the firmware

via network.

• This setting cannot be selected if you do not

have Internet access or there is no updatable

firmware.

Update via

USB

Press ENTER to select when updating the firmware

via USB.

• This setting cannot be selected if a USB storage

device is not connected or there is no updatable

firmware in the USB storage device.

•

Wait for a while if "Firmware Update" cannot be selected. It can be selected when the

network function is activated.

Initial Setup

Make the initial setup from the setup menu.

•

Wait for a while if "Initial Setup" cannot be selected. It can be selected when

the network function is activated.

Lock

Lock the Setup menu so that the settings cannot be changed.

Setting Item

Default Value

Setting Details

Setup Parameter Unlocked

Lock the Setup menu so that the settings cannot be

changed.

“Locked”: The menu is locked.

“Unlocked”: The menu is unlocked.

Summary of Contents for VSX-933




































































































































Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands

Pioneer VSX-933, Instruction Manual

Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands