Pioneer VSX-933 Instruction Manual Download Page 72

Page: 72 / 131

≫

≫

≫

≫

≫

≫

Selectable listening modes

You can select a variety of listening modes

according to the audio format of the signal to be

input.

• The Stereo mode can be selected with any audio

format.

• When analog signals are being input in the Pure

Direct mode, the modes switches to the Analog

Direct mode which passes signals directly to the

amplifier without passing through the DSP (Digital

Signal Processor).

• Listening modes available when headphones are

connected are Pure Direct and Stereo only.

Selectable listening modes

Input Format

Listening Mode

Analog

Stereo
Mono

DSur

DTS Neural:X

Classical

Unplugged

Ent.Show

Drama

AdvancedGame

Action

Rock/Pop

Sports

Ext.Stereo

Ext.Mono

F.S.Surround

Surround speakers or height speakers need to be installed.

A center speaker, surround speakers, or height speakers need to be

installed.

Input Format

Listening Mode

PCM

Music files (except DSD/

Dolby TrueHD)

Stereo
Mono

DSur

DTS Neural:X

Classical

Unplugged

Ent.Show

Drama

AdvancedGame

Action

Rock/Pop

Sports

Ext.Stereo

Ext.Mono

F.S.Surround

Surround speakers or height speakers need to be installed.

A center speaker, surround speakers, or height speakers need to be

installed.

Summary of Contents for VSX-933




































































































































Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands

Pioneer VSX-933, Instruction Manual

Search results

Summary of Contents for VSX-933

Reviews:

Related manuals for VSX-933

Brands by name

Popular brands