Controls and displays
04
25
En
6
(TUNE/ST) /
ENTER
Use the arrow buttons when setting up your surround
sound system (page 33) and the AV options (page 61).
Also used to control DVD menus/options and for deck 1
of a double cassette deck player. Use the
TUNE
/
buttons to find radio frequencies and use
ST
/
to
find preset stations (page 31).
7
TV CONTROL buttons
These buttons are dedicated to control the TV assigned to
the
TV CTRL
button. Thus if you only have one TV to hook
up to this system assign it to the
TV CTRL
input source
button. If you have two TVs, assign the main TV to the
TV
CTRL
button (see page 65 for more on this).
TV
– Use to turn on/off the power of the TV.
TV VOL +/–
– Use to adjust the volume on your TV.
INPUT SELECT
– Use to select the TV input signal.
TV CH +/–
– Use to select channels.
8
Component control buttons
The main buttons (
,
, etc.) are used to control a
component after you have selected it using the input
source buttons.
The controls above these buttons can be accessed after
you have selected the corresponding input source button
(for example
DVD
,
DVR1
or
TV
). The following controls
can be accessed when listening to the built-in tuner:
MPX
– Switches between stereo and mono reception
of FM broadcasts. If the signal is weak then switching
to mono will improve the sound quality (page 31).
DISP
– Switches between named station presets and
radio frequencies (page 32).
9
STATUS
Press to check selected receiver settings (page 63).
10
MULTI OPE
Use this button to perform multi operations (page 67).
11
SHIFT
Press to access the controls outlined in white boxes (for
example,
INPUT SELECT
), or to display the currently
selected input source in the remote control LCD.
12
SOURCE
Press to turn on/off other components connected to the
receiver (see page 65 for more on this).
13 Character display (LCD)
This display shows information when transmitting
control signals.
The following commands are shown when you’re setting
the remote to control other components (see
Controlling
the rest of your system
on page 65):
SETUP
– Indicates the setup mode, from which you
choose the options below.
PRESET
– See
Selecting preset codes directly
on
page 65.
LEARNING
–
See
Programming signals from other
remote controls
on page 65.
MULTI OP
– See
Multi Operation and System Off
on
page 67.
SYS OFF
– See
Multi Operation and System Off
on
page 67.
DIRECT F
– See
Direct function
on page 67.
RENAME
– See
Renaming input source names
on
page 67.
ERASE
– See
Erasing one of the remote control button
settings
on page 66.
RESET
– See
Resetting the remote control presets
on
page 66.
READ ID
– See
Confirming preset codes
on page 66.
14 RECEIVER
Switches the remote to control the receiver (used to
select the green commands above the number buttons
(
ANALOG ATT
, etc)). Also use this button to set up
surround sound (page 8, page 33). With
SHIFT
, this
selects the multi-room control (page 53).
15 VOL +/–
Use to set the listening volume.
16 MUTE
Mutes the sound or restores the sound if it has been
muted (adjusting the volume also restores the sound).
17 Receiver controls
SIGNAL SEL
– Use to select an input signal (page 29).
SBch
– Use to select the surround/virtual back
channel mode (page 29).
STEREO
– Switches between direct and stereo
playback. Direct playback bypasses the tone controls
and any other signal processing for the most
accurate reproduction of a source (page 28).
THX
– Press to select a Home THX listening mode
(page 27).
STANDARD
– Press for Standard decoding and to
switch between the various
2
Pro Logic IIx and
Neo:6 options (page 26).
ADV.SURR
– Use to switch between the various
surround modes
(page 27).
18 PHASE
– Press to switch on/off Phase Control
(page 10).
MCACC
– Press to switch between MCACC presets
(page 28).
S.DIRECT
– Press to select Auto Surround (page 26)
or Stream Direct (page 28) listening.
VSX-9110TXV_KU.book.fm 25 ページ ２００６年４月４日 火曜日 午後５時１５分
