Listening to your system
4
4
24
Using the Sound Retriever
When audio data is removed during the compression
process, sound quality often suffers from an uneven sound
image. The Sound Retriever feature employs new DSP
technology that helps bring CD quality sound back to
compressed 2-channel audio by restoring sound pressure
and smoothing jagged artifacts left over after compression.
…
Press
S.RETRIEVER
to switch the S.RTV (Sound
Retriever) ON or OFF.
Note
•
The Sound Retriever mode cannot be set to
ON
, when the
DIRECT
mode or the
PURE DIRECT
mode is switched on.
Better sound using Phase Control
This receiver’s Phase Control feature uses phase correction
measures to make sure your sound source arrives at the
listening position in phase, preventing unwanted distortion
and/or coloring of the sound.
Phase Control technology provides coherent sound
reproduction through the use of phase matching for an
optimal sound image at your listening position. The default
setting is on and we recommend leaving Phase Control
switched on for all sound sources.
…
Press
PHASE
to switch the P.CTL (Phase Control) ON or OFF.
Note
•
Phase matching is a very important factor in achieving proper
sound reproduction. If two waveforms are ‘in phase’, they
crest and trough together, resulting in increased amplitude,
clarity and presence of the sound signal. If a crest of a wave
meets a trough, then the sound will be ‘out of phase’ and an
unreliable sound image will be produced.
•
If your subwoofer has a phase control switch, set it to the
plus (+) sign (or 0°). However, the effect you can actually
feel when Phase Control is set to
ON
on this receiver
depends on the type of your subwoofer. Set your
subwoofer to maximize the effect. It is also recommended
you try changing the orientation or the place of your
subwoofer.
•
Set the built-in lowpass filter switch of your subwoofer to
OFF. If this cannot be done on your subwoofer, set the
cutoff frequency to a higher value.
•
If the speaker distance is not properly set, you may not
have a maximized Phase Control effect.
•
The Phase Control mode cannot be set to
ON
in the
following cases:
-
When the
PURE DIRECT
mode is switched on.
-
When the headphones are connected.
Setting the Audio options
There are a number of additional sound settings you can
make using the
AV ADJUST
menu. The defaults, if not
stated, are listed in bold.
Important
•
Note that if a setting doesn’t appear in the
AV ADJUST
menu, it is unavailable due to the current source, settings
and status of the receiver.
1
Press
AV ADJUST
button.
2
Use
/
to select the setting you want to adjust.
Depending on the current status/mode of the receiver,
certain options may not be able to be selected. Check
the table below for notes on this.
3
Use
/
to set it as necessary.
See the table below for the options available for each
setting.
4
Press
RETURN
to confirm and exit the menu.
PHASE
PHASE
PHASE
PHASE
S.RETRIEVER
S.RETRIEVER
BT AUDIO
BT AUDIO
BASS
BASS
USB
USB
TUN
TUN
AUX
AUX
BT
BT
Setting/What it does
Option(s)
S.DLY
(Sound Delay)
Some monitors have a slight delay when
showing video, so the soundtrack will be
slightly out of sync with the picture. By adding
a bit of delay, you can adjust the sound to
match the presentation of the video.
0 ms to 500 ms
(1 step : 5 ms)
Default:
0
MIDNIGHT
/
LOUDNESS
The
MIDNIGHT
allows you to hear effective
surround sound of movies at low volumes.
The
LOUDNESS
is used to get good bass and
treble from music sources at low volumes.
M/L OFF
MIDNIGHT
LOUDNESS
AV
AV
ADJUST
ADJUST
AV
ADJUST
AV
ADJUST
MUTE
MUTE
HOME
HOME
MENU
MENU
RETURN
RETURN
RETURN
RETURN
VOLUME
VOLUME
VSX-531-K_CDC_En.book 24 ページ ２０１６年２月３日 水曜日 午後３時３４分
