Pioneer VSA-E03 Operating Instructions Manual Download

Page: 30 / 48

Press AMP.

This sets the remote to select the sound mode.

(You can skip this step when using the controls on the amplifier.)

Press DSP MODE to select the sound mode.

Each press changes the DSP mode as follows:

Selecting a Sound Mode

To ensure the best possible surround sound, be sure to complete the set up procedures described in “Setting Up for
Surround Sound” (starting on page 14) before using the sound modes. This is particularly important when using the

(Dolby) Surround mode. When using the sound modes, SPEAKERS A are used. If SPEAKERS B are selected and a

sound mode is turned on, selection automatically switches to SPEAKERS A only.

Surrround operation

Sound Modes

HALL 1

HALL 2

JAZZ

DANCE

SFC OFF

THEATER 2

THEATER 1

• The amount of effect of each DSP mode can be adjusted in the range of 10

to 90 (the default setting value is 70) by pressing EFFECT –/+.

DVD/LD

VCR 1

TV/SAT

TUNER

VCR 2

MD/TAPE

TV CONTROL

AMP

DSP MODE

CH.SELECT

ATT SIG.SELECT

MIDNIGHT

TEST TONE

AUDIO/VIDEO PRE-PROGRAMMED

REMOTE CONTROL UNIT

+10

TV/VCR

CLASS

CHANNEL

MULTI CONTROL

ENTER

VOL

–

TV FUNC

AMP

MUTING

CH.LEVEL

EFFECT

FL DIMMER

FUNCTION

DIRECT

MODE CHECK

COMMANDER

SET UP

MEMU

EFFECT –/+

memo

Summary of Contents for VSA-E03

















































Search results

Summary of Contents for VSA-E03

Reviews:

Related manuals for VSA-E03

Brands by name

Popular brands

Pioneer VSA-E03, Operating Instructions Manual

Search results

Summary of Contents for VSA-E03

Reviews:

Related manuals for VSA-E03

Brands by name

Popular brands