background image

www.pioneercoverall.com

   

 

 

11 

 

 

 

866-353-5826 

 

 

 

                                                      TIPS FOR THE OPERATOR 
 

1.

 

Make sure the truck is clear of overhead obstructions before operating the unit. 

2.

 

Do not operate under any overhead wires. 

3.

 

Keep Hands clear of any moving parts. 

4.

 

Make sure nobody is inside the container, or in the path of the arms before 
operating the unit. 

5.

 

Pay attention to safety decals. 

6.

 

Release the valve as soon as the Rear Section contacts the rear of the container, or 
when the Arms are seated on the Bearing plates. 

7.

 

Release the valve when the Gantry has been fully extended or retracted. 

 
 
                                               SPECIAL NOTE 
  

    NOT MANUFACTURED OR INTENDED FOR USE WITH HAZARDOUS WASTE 
 
 
        Pioneer Consolodated Corporation will not be held responsible for damages to, or  
        caused by their container covering systems when they have not been installed or  
        used in the manner prescribed in this manual. 
        Any modifications to the unit or deviations from the procedures outlined in this 
        manual must be authorized in writing by Pioneer Consolodated Corp. 
 
 
                                                   WARRANTY 
 
       Pioneer Consolodated Corp oration warrants this automatic container covering  
       system for a period of (90) days, against proven defective parts and workmanship. 
       Our liability is limited to the replacement parts and does not include freight, labor 
       or lost time due to or in connection with the failure of the parts. Any part will be 
       replaced under the conditions of this warranty when Pioneer Consolodated Corp. 
       has authorized a return and has received satisfactory evidence that the part(s) is 
       (are) defective. 

Summary of Contents for HR 1500 PTO















Reviews: