Pioneer ELITE VSX-LX505 Instruction Manual Download Page 145

Page: 145 / 212

145

Setup

Hardware

Network Standby (Default Value: On)

When this function is set to "On", the network function works even in standby

state, and you can turn on the power of the unit via network using an

application such as Pioneer Remote App that can control this unit.

•

When this function is set to "On", the power consumption in standby state

increases, however, the increase in power consumption is minimized

by automatically entering the HYBRID STANDBY mode where only the

essential circuits operate.

Note that even if this function is set to "Off", when any of the HDMI CEC

(

→

p142

), HDMI Standby Through (

→

p142

), USB Power Out at Standby

(

→

p144

) and Bluetooth Wakeup (

→

p145

) functions is enabled, this

function will be in "On" state regardless of the setting.

•

When connection to the network is lost, "Network Standby" may be disabled

to reduce power consumption. In such a case, turn the unit on by using the

power button on the remote controller or main unit.

Bluetooth Wakeup (Default Value: Off)

This function wakes up the unit on standby by connecting a BLUETOOTH

enabled device. This is effective when "Bluetooth" - "Bluetooth Receiver" is set

to "On".

When this function is used

•

When this function is set to "On", the power consumption

in standby state increases, however, the increase in power

consumption is minimized by automatically entering the

HYBRID STANDBY mode where only the essential circuits

operate.

Off

When this function is not used

• This setting is fixed to "Off" if "Network/Bluetooth" -

"Bluetooth" - "Bluetooth Receiver" is set to "Off".

• This setting is also fixed to "Off" if "Network/Bluetooth" -

"Bluetooth" - "Bluetooth Receiver" - "Auto Input Change" is

set to "Off".

•

Wait for a while if "Network Standby" and "Bluetooth Wakeup" cannot be

selected. It can be selected when the network function is activated.

Summary of Contents for ELITE VSX-LX505





















































































































































































































Search results

Summary of Contents for ELITE VSX-LX505

Reviews:

Related manuals for ELITE VSX-LX505

Brands by name

Popular brands

Pioneer ELITE VSX-LX505, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX505

Reviews:

Related manuals for ELITE VSX-LX505

Brands by name

Popular brands