Pioneer ELITE VSX-LX304 Instruction Manual Download Page 61

Page: 61 / 180

≫

≫

≫

≫

≫

≫

Network Connection

This unit can be connected to the network using a wired LAN or Wi-Fi (wireless

LAN). You can enjoy network functions such as Internet radio by network

connection. If connection is made by the wired LAN, connect the router and the

NETWORK jack with the LAN cable as shown in the illustration. To connect by

Wi-Fi, select "Wireless" for "5. Network Connection" in Initial Setup (

p161

select your desired setting method, and then follow the on-screen instructions.

To configure the setting on the System Setup menu after the completion of Initial

Setup, press the

button on the remote controller to display the Home screen,

and select "Network/ Bluetooth" - "Network" to make the setting.

(

p153

) For

the Wi-Fi connection, stand the wireless antenna for use.

LAN cable

Summary of Contents for ELITE VSX-LX304





















































































































































































Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands

Pioneer ELITE VSX-LX304, Instruction Manual

Search results

Summary of Contents for ELITE VSX-LX304

Reviews:

Related manuals for ELITE VSX-LX304

Brands by name

Popular brands