48
04
Basic Setup
Now Analyzing...
2/9
Environment Check
1a.Full Auto MCACC
A/V RECEIVER
Exit
Cancel
Ambient Noise
: OK
Microphone
:
Speaker YES/NO :
L
:
YES
FHL
:
YES
C
:
YES
FHR
:
YES
R
:
YES
SR
:
YES
SBR :
YES
SBL
:
YES
SL
:
YES
SW
:
YES
1a.Full Auto MCACC
10
OK
RETRY
A/V RECEIVER
Exit
Cancel
The configuration shown on-screen should reflect the actual speakers you have.
!
If you see an
ERR
message (or the speaker configuration displayed isn’t correct), there may be a problem
with the speaker connection. If selecting
RETRY
doesn’t work, turn off the power and check the speaker con-
nections. If there doesn’t seem to be a problem, you can simply use
i
/
j
to select the speaker and
k
/
l
to
change the setting and continue.
!
If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the
phase (dipole speakers, reflective speakers, etc.),
Reverse Phase
may be displayed even if the speakers are
properly connected.
If
Reverse Phase
is displayed, the speaker’s wiring (+ and –) may be inverted. Check the speaker
connections.
—
If the connections were wrong, turn off the power, disconnect the power cord, then reconnect properly.
After this, perform the Full Auto MCACC procedure again.
—
If the connections were right, select
GO NEXT
and continue.
7 Make sure ‘OK’ is selected, then press ENTER.
A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum
receiver settings.
Again, try to be as quiet as possible while this is happening. It may take 3 to 10 minutes.
8 The Full Auto MCACC Setup procedure is completed and the Home Menu menu reappears
automatically.
Be sure to disconnect the microphone from this receiver upon completion of the Full Auto MCACC Setup.
The settings made in the Full Auto MCACC Setup should give you excellent surround sound from your system,
but it is also possible to adjust these settings manually using
The Advanced MCACC menu
on
page 92
or
The
System Setup and Other Setup menus
on
page 100
.
!
Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12
cm (5 inches) will end up with different size settings. You can correct the setting manually using the
Manual
speaker setup
on
page 101
.
!
The subwoofer distance setting may be farther than the actual distance from the listening position. This set-
ting should be accurate (taking delay and room characteristics into account) and generally does not need to
be changed.
!
If Full Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and view-
ing environment, we recommend adjusting the settings manually.
Problems when using the Auto MCACC Setup
If the room environment is not optimal for the Auto MCACC Setup (too much background noise, echo off the
walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect. Check for
household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them
off if necessary. If there are any instructions showing in the front panel display, please follow them.
!
Some older TVs may interfere with the operation of the microphone. If this seems to be happening, switch off
the TV when doing the Auto MCACC Setup.
The Input Setup menu
You only need to make settings in the
Input Setup
menu if you didn’t hook up your digital equipment according
to the default settings (see
Input function default and possible settings
on
page 49
). In this case, you need to tell
the receiver what equipment is hooked up to which terminal so the buttons on the remote control correspond to
the components you’ve connected.
!
The on-screen display is only displayed when this receiver’s
HDMI OUT 1
or
HDMI OUT 2
terminal is con-
nected to the TV’s HDMI input terminal by HDMI cable. When connected to the TV with anything other than an
HDMI cable, watch the front panel display when performing operations and making settings.
1 Press
on the remote control, then press HOME MENU.
A Graphical User Interface (GUI) screen appears on your TV. Use
i
/
j
/
k
/
l
and
ENTER
to navigate through the
screens and select menu items. Press
RETURN
to exit the current menu.
2 Select ‘System Setup’ from the Home Menu.
3 Select ‘Input Setup’ from the System Setup menu.
A/V RECEIVER
Exit
Return
a.Manual SP Setup
b. Input Setup
c. OSD Language
d. Network Setup
e. HDMI Setup
f. Other Setup
g. MHL Setup
4.System Setup
4b.Input Setup
A/V RECEIVER
Exit
Return
Input
:
DVD
Input Name
:
Rename
Audio In
:
COAX-1
HDMI Input
:
Input-1
Input Skip
:
OFF
Component In
:
In-1
12V Trigger 1
:
OFF
12V Trigger 2
:
OFF
4 Select the input function that you want to set up.
The default names correspond with the names next to the terminals on the rear panel (such as
DVD
or
SAT/CBL
which, in turn, correspond with the names on the remote control.
5 Select the input(s) to which you’ve connected your component.
For example, if your DVD player only has an optical output, you will need to change the
DVD
input function’s
Audio In
setting from
COAX-1
(default) to the optical input you’ve connected it to. The numbering (
OPT-1
to
OPT-2
) corresponds with the numbers beside the inputs on the back of the receiver.
6 When you’re finished, proceed to the settings for other inputs.
There are optional settings in addition to the assignment of the input jacks:
!
Input Name
– You can choose to rename the input function for easier identification. Select
Rename
to do so,
or
Default
to return to the system default.
!
Input Skip
– When set to
ON
, that input is skipped when selecting the input using
INPUT SELECT
. (
DVD
and
other inputs can be still be selected directly with the input function buttons.)
!
12V Trigger 1/2
– After connecting a component to one of the 12 volt triggers (see
Switching components
on and off using the 12 volt trigger
on
page 45
), select
MAIN
,
ZONE 2
,
ZONE 3
,
HDZONE
or
OFF
for the cor-
responding trigger setting to switch it on automatically along with the (main or sub) zone specified.
—
Devices connected to 12 volt triggers can be associated with
HDMI OUT
switching. For details, see
HDMI
Setup
on
page 73
.
7 When you’re finished, press RETURN.
You will return to the
System Setup
menu.
