Pioneer DRM-3000, Operating Instructions Manual

Page: 12 / 228

12
<DRC1184>
En
TO AVOID PROBLEMS
The following is a list of operation items that may potentially lead to problems in component functioning.
1. Installation
2. Connections
3. Power ON/OFF
4. Control
5. Transporting Unit
6. Error Correction
Potential Malfunction/Error Issue
÷
Do not place foreign objects inside the changer, since malfunction
may result.
÷
Do not use the changer in locations subject to high concentrations
of dust, heat, or humidity.
* Do not install in locations directly exposed to outdoor dust or air.
* Do not install near air conditioner vents or air cleaners.
÷
Do not subject the recorder to impact or vibration during use.
* Do not install in hallways or other areas near frequent pedestrian
traffic.
÷
When connecting exterior SCSI cable, be sure that power is first
turned off to host computer and changer.
* When connecting internal SCSI cable, power may be left while
connecting.
÷
When installing a drive, be sure to connect the changer interface
cable to the connector corresponding to the bay in which the drive
is installed. If the cable is mistakenly connected to a neighboring
connector, the discs may be damaged and the
E99 error may occur.
÷
Be sure to set the terminator switch to ON on the final component
connected to the SCSI bus. If it is mistakenly set to OFF, the changer
operation may be unstable. If malfunctions occur with the switch
set to OFF, set the switch to ON and turn the power on again.
* When a component's terminator switch is set to ON, if the com-
ponent is subsequently removed from the SCSI bus, or if the
component's SCSI cable is disconnected, the condition immedi
ately reverts to the same state as when the terminator is OFF,
thus resulting in the same condition as above.
÷
When installing a drive, if the wiring monitor indicator does not flash,
recheck and install the power cable connection, followed by the
changer interface connection.
÷
Never disconnect power while the changer is transporting a disc, or
when the writer is recording data to a disc.
÷
When turning the power off and then on again, wait at least ten
seconds after turning the power off before turning it on again.
÷
During data recording, do not send commands from the disc writer
to remove disc (
Move Medium, Rezero Unit ), since EC
❋
error or
write malfunction may occur (back buffer underrun).
÷
When transporting the unit, pack the unit in its original packaging
materials, and ship in an upright position. Do not transport the unit
on its side.
÷
Do not transport the unit with drive units, 50-disc magazines or other
optional accessories loaded (except for 20-disc hyper-magazine).
When transporting the accessories, repack them in their original
packaging materials.
÷
Do not transport disc magazines with discs loaded.
÷
E8
❋
, E9
❋
, EF8 , or EF3 errors cannot be corrected merely by reset-
ting the changer's power on/off. The system administrator mode
must be used to open and then close the door again. For these and
other errors, see the Operating Instructions, p. 44.
÷
[ E83 ], [ E99 ], [ E88 ]
÷
Recording/playback mal-
function
÷
Recording/playback mal-
function
÷
Changer malfunction
÷
[ E83 ], [ E99 ]
÷
Display window (LCD)
doesn't appear correctly.
÷
Operation keys malfunc-
tion.
÷
Changer not recognized
on the SCSI.
÷
Changer does not detect
drive.
÷
Changer malfunction.
÷
Data recording malfunc-
tion
÷
Recording malfunction
÷
[ EC
❋
], (where
❋
= 0 – F )
÷
[ E8
❋
], [ E9
❋
], [ EF8 ], [ EF3 ]
(where
❋
= 0 – F )