Pioneer DJM 909 - Battle Mixer W/Effects, Service Manual

Page: 153 / 156

DJM-909
153
5 6 7 8
5 6
7
8
C
D
F
A
B
E
31 CH-2 output On/Off lever (TRANSFORM)
Use to set CH-2 output to On or Off (Mute).
This lever’s setting angle can be changed in 45
°
increments
(changing of the angle should be performed by an authorized
Pioneer service technician).
32 CH-2 REVERSE indicator
When lighted, indicates that the front panel’s FADER REVERSE
switch has been set so that the CH-2 fader lever operates in the
reverse direction (see front panel item 52).
33 MASTER LEVEL display button and indicator
When depressed to the On position, the indicator lights and the
level meters display the master output (stereo) peak levels. When
turned Off, the level meters display the peak levels for CH-1 (left)
and CH-2 (right) (see also item 26).
34 CH-2 fader lever
The CH-2 fader lever is used to control the level of signals sent to
the cross fader. Signal level is maximum at scale mark “10,” and
minimum at scale mark “0”.
When the front panel CH-2 FADER REVERSE switch is set to
[ON], the signal level is maximum at scale mark “0,” and
minimum at scale mark “10”.
∗
The channel fader curve can be adjusted by means of the front
panel FADER CURVE dials.
35 CH-2 FADER START indicator
Lights when the CH-2 fader start/back cue function is enabled
(see also top panel item 30 and front panel item 53).
36 C.F.2 FADER START indicator
Lights when CH-2 cross-fader start/back cue function is enabled
(see also top panel item 30 and front panel item 53).
37 Touch Panel
Touch this screen to set effects in accordance with the displayed
menus.
∗
The panel’s screen contrast and backlight luminance can be
adjusted (see rear panel items 61 and 63).
38 CH-1 effect bank buttons and indicators
(BANK 1, 2, 3)
When one of these buttons is pressed, the indicator lights and the
corresponding preset effect is enabled. Each BANK button can be
recorded with three effects for CH-1 (at time of shipping, the
buttons have been factory preset with typically used effects).
BANK 1 is selected in the default condition bafter power is initially
turned on.
39 CH-1 effect parameter adjust button (FX ADJ.)
Press to display the touch panel’s CH-1 effect parameter adjust
menu.
40 Fader curve display and CH-1 effect select
button (FADER CURVE/BANK EDIT)
Press to display the fader curve on the touch panel. Holding the
button depressed for about one second will cause the touch panel
to display the CH-1 effect select menu.
41 CH-1 effect time adjust/select dial
(TIME/SELECT)
Use to adjust the time parameters of effects applied to CH-1
(rotate clockwise to lengthen, counterclockwise to shorten).
When the effect select menu is displayed, causes the effects list to
scroll.
42 CH-1 effect mix ratio/depth adjust dial
(MIX/DEPTH)
Use to adjust the volume (amount) of effects applied to CH-1
(rotate clockwise to increase effects, counterclockwise to reduce).
43 CH-1 effect switch and indicator
(EFFECT LOCK ON/OFF/ON)
To turn effects [ON], either pull switch forward (switch returns
automatically to [OFF] when released) or slide to far side to the
[LOCK ON] position. When effects are [ON], the indicator flashes
and effects are applied to CH-1.
44 CH-1 TAP button
Under normal conditions, the automatic BPM counter operates to
display the track’s BPM value on the touch panel.
Automatic BPM counting may be difficult with some tracks,
however. In such cases, or if you wish to deliberately set a
different BPM, use the TAP button.
• The BPM value can be changed by rotating the TIME/ SELECT
dial while holding the TAP button depressed.
• Tapping the button in time with the beat will cause the function to
switch to the manual BPM count mode; the tapped beat will be
counted and displayed as the BPM value. Returning to the auto
BPM mode is performed from the effect parameter adjust screen
45 CH-2 effect bank buttons and indicators
(BANK 1, 2, 3)
When one of these buttons is pressed, the indicator lights and the
corresponding preset effect is enabled. Each BANK button can be
recorded with three effects for CH-2 (at time of shipping, the
buttons have been factory preset with typically used effects).
BANK 1 is selected in the default condition after power is initially
turned on.
46 CH-2 effect parameter adjust button (FX ADJ.)
Press to display the touch panel’s CH-2 effect parameter adjust
menu.
47 Fader curve display and CH-2 effect select button
(FADER CURVE/BANK EDIT)
Press to display the fader curve on the touch panel. Holding the
button depressed for about one second will cause the touch panel
to display the CH-2 effect select menu.
48 CH-2 effect time adjust/select dial (TIME/SELECT)
Use to adjust the time parameters of effects applied to CH-2
(rotate clockwise to lengthen, counterclockwise to shorten).
When the effect select menu is displayed, causes the effects list to
scroll.
49 CH-2 effect mix ratio/depth adjust dial (MIX/DEPTH)
Use to adjust the volume (amount) of effects applied to CH-2
(rotate clockwise to increase effects, counterclockwise to
reduce).