DJM-707
126
1
2
3
4
1
2
3
4
C
D
F
A
B
E
5 CH-1 equalizer dials (HI/MID/LOW)
HI
Use to adjust CH-1 input treble response
(range of adjustment: 13 kHz, +6 dB to –26 dB).
MID
Use to adjust CH-1 input midrange response
(range of adjustment: 1 kHz, +6 dB to –26 dB).
LOW
Use to adjust CH-1 input bass response
(range of adjustment: 70 Hz, +6 dB to –26 dB).
6 MIC SEND button and indicator
When set to On, the indicator lights, and microphone signals are
output at the SEND jacks.
7 Session input level dial (SESSION IN)
Use to adjust the session input volume
(range of adjustment: 0 dB to –).
8 CH-1 SEND button and indicator
When set to On, the indicator lights, and CH-1 signals are output
at the SEND jacks.
9 CH-1 EQ ON/OFF switch and indicator
When set to [ON], the indicator lights and CH-1 equalizer is
enabled.
When set to [OFF], the indicator goes out and the equalizer circuit
is bypassed.
10 CH-2 input selector switch
(PHONO 2/LINE 2 – CD 2)
Use to select input signal from CH-2 PHONO/LINE input jacks, or
CH-2 CD input jacks, and send them to the TRIM control.
11 CH-2 TRIM dial
Use to adjust the CH-2 input signal level
(range of adjustment: +9 dB to –).
12 MASTER LEVEL dial
User to adjust the master output volume level
(range of adjustment: 0 dB to –).
13 Booth monitor level dial
(BOOTH/SESSION OUT)
Use to adjust the volume level of signals at the BOOTH/ SESSION
OUT jacks (range of adjustment: 0 dB to –).
This level can be set independently of the setting of the MASTER
LEVEL dial.
14 Headphones level dial (PHONES)
Use to adjust the volume level of the headphones output
(range of adjustment: 0 dB to –).
15 Monitor SELECT switch
MASTER position
selects MASTER output. (This setting allows output
regardless of the setting of the MASTER LEVEL dial.)
CUE position
selects the channel adjusted with the headphone mixing lever (17).
16 CH-2 equalizer dials (HI/MID/LOW)
HI
Use to adjust CH-2 input treble response
(range of adjustment: 13 kHz, +6 dB to –26 dB).
MID
Use to adjust CH-2 input midrange response
(range of adjustment: 1 kHz, +6 dB to –26 dB).
LOW
Use to adjust CH-2 input bass response
(range of adjustment: 70 Hz, +6 dB to –26 dB).
17 Headphone mixing lever (CH-1 – CH-2)
This lever does not function when the monitor SELECT switch (15)
is set to [MASTER].
When the monitor SELECT switch (15) is set to [EFFECT] or [CUE],
moving the lever to the left side produces CH-1 monitor output,
while moving it to the right produces CH-2 monitor output.
Centering the lever at the center detent position produces balanced
output of CH-1 and CH-2 signals.
18 CH-2 SEND button and indicator
When set to On, the indicator lights, and CH-2 signals are
output at the SEND jacks.
19 CH-2 EQ ON/OFF switch and indicator
When set to [ON], the indicator lights and the CH-2 equalizer is
enabled.
When set to [OFF], the indicator goes out and the equalizer circuit
is bypassed.
20 POWER indicator
Lights when power is turned On.
21 CH-1 FADER START button
When this button is set to On, fader start and back cue can be
performed on the CH-1 CD player.
Whether the operation is initiated by operation of the CH-1 fader
lever, or by the cross fader lever is determined by the position of
the front panel’s FADER START selector switch; the selection is
indicated by the lighting of the top panel’s CH-1 FADER START
indicator or C.F.1 FADER START indicator.
22 CH-1 output On/Off lever (TRANSFORM)
Use to set CH-1 output to On or Off (Mute).
The lever’s setting angle can be changed in 45
°
increments
(changing of the angle should be performed by an authorized
Pioneer service technician).
23 CH-1 REVERSE indicator
When lighted, indicates that the front panel’s FADER REVERSE
switch has been set so that the CH-1 fader lever operates in the
reverse direction (see front panel item 38).
24 CH-1 fader lever
The CH-1 fader lever is used to control the level of signals sent to
the cross fader. Signal level is maximum at scale mark “10,” and
minimum at scale mark “0”.
When the front panel CH-1 FADER REVERSE switch is set to
[ON], the signal level is maximum at scale mark “0,” and minimum
at scale mark “10”.
∗
The channel fader curve can be adjusted by means of the
front panel FADER CURVE dials.
25 CH-1 FADER START indicator
Lights when the CH-1 fader start/back cue function is enabled
(see also top panel item 21 and front panel item 39).
26 C.f.1 FADER START indicator
Lights when the CH-1 cross-fader start/back cue function is enabled
(see also top panel item 21 and front panel item 39).
Summary of Contents for DJD-707
