SLA
(source level adjustment)
SLA
(Source level adjustment) lets you adjust the vo-
lume level of each source to prevent radical changes
in volume when switching between sources.
!
When selecting FM as the source, you cannot
switch to
SLA
.
!
Settings are based on the FM volume level, which
remains unchanged.
Before adjusting source levels, compare the FM
volume level with the level of the source you wish
to adjust.
!
The AM volume level can also be adjusted with
source level adjustments.
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to adjust the source volume.
Adjustment range:
+4
to
–
4
3
Press
M.C.
to confirm the selection.
Note
Operation is complete even if the menu is can-
celled before being confirmed.
Initial Settings
1
Press SRC/OFF and hold until the unit
turns off.
2
Press M.C. and hold until the initial set-
ting menu appears in the display.
3
Turn M.C. to select the initial setting.
After selecting, perform the following proce-
dures to set the initial setting.
Clock
(setting the clock)
1
Press
M.C.
to display the setting mode.
2
Press
M.C.
to select the segment of the clock dis-
play you wish to set.
Hour
—
Minute
As you select segments of the clock display, the
selected segment flashes.
3
Turn
M.C.
to adjust the clock.
Clock
(clock on/off setting)
1
Press
M.C.
to turn the clock display on or off.
AUX1
/
AUX2
(auxiliary input setting)
Activate this setting when using auxiliary device con-
nected to this unit.
1
Press
M.C.
to turn
AUX
on or off.
USB PnP
(plug and play)
This setting allows you to switch your source to
USB
/
USB-iPod
automatically.
1
Press
M.C.
to turn the plug and play on or off.
ON
–
When USB storage device/iPod is con-
nected, the source is automatically switched to
USB
/
USB-iPod
. If you disconnect your USB sto-
rage device/iPod, this unit
’
s source is turned off.
OFF
–
When USB storage device/iPod is con-
nected, the source is not switched to
USB
/
USB-
iPod
automatically. Please change the source to
USB
/
USB-iPod
manually.
Brightness
(display brightness setting)
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to switch the brightness setting.
High
(high)
—
Low
(low)
3
Press
M.C.
to confirm the selection.
SW control
(rear output and subwoofer setting)
The rear speaker leads output (
Rear SP
) and RCA out-
put (
Preout
) of this unit can be used for full-range
speaker (
Rear SP
:
FULL
/
Preout
:
Rear
) or subwoofer
(
Rear SP
:
SUBW
/
Preout
:
SUBW
) connection. If you
switch to
Rear SP
:
SUBW
, you can connect a rear
speaker lead directly to a subwoofer without using an
auxiliary amp.
Initially,
Rear SP
is set for rear full-range speaker con-
nection (
FULL
). When
Rear SP
:
FULL
is selected, you
can connect the RCA output to a subwoofer. In this
case, you can select whether to use the subwoofer
controller
’
s (low pass filter, phase) built-in
Preout
:
SUBW
or the auxiliary
Preout
:
Rear
.
1
Press
M.C.
to display the setting mode.
2
Press
M.C.
to cycle between as following:
Rear SP
/
Preout
—
FULL
(
SUBW
)/
SUBW
(
Rear
)
3
Turn
M.C.
to change the setting.
Rear SP
:
FULL
—
SUBW
Preout
:
SUBW
—
Rear
!
Even if you change this setting, there is no
output unless you turn the subwoofer output
on (refer to
SW setting 1
(subwoofer on/off
setting)
on the previous page).
!
If you change this setting, subwoofer output
in the audio menu will return to the factory
settings.
DEMO
(demo display setting)
1
Press
M.C.
tp turn the demo display on or off.
Operating this unit
En
15
English
Section
02
