29
EN
G
L
IS
H
Initial Settings
Switching Auto PI Seek
The unit can automatically search for a different station with the same programming,
even during preset recall.
1. Press FUNCTION to select A-PI.
Press
FUNCTION
repeatedly until
A-PI
appears in the display.
2. Press
8
or
2
to turn A-PI on or off.
Pressing
8
or
2
will turn
A-PI
on or off and that status will be displayed (e.g.,
A-PI
:ON
).
Switching the auxiliary setting
Auxiliary equipments connected to this unit can be activated individually. Set each
AUX source to ON when using. About connecting or using auxiliary equipments, refer
to “Using the AUX source” on page 30.
1. Press FUNCTION to select AUX1/AUX2.
Press
FUNCTION
repeatedly until
AUX1
/
AUX2
appears in the display.
2. Press
8
or
2
to turn AUX1/AUX2 on or off.
Pressing
8
or
2
will turn
AUX
on or off and that status will be displayed (e.g.,
AUX1
:ON
).
Setting the rear output and subwoofer controller
This unit’s rear output (rear speaker leads output and RCA rear output) can be used
for full-range speaker (
R-SP :FUL
) or subwoofer (
R-SP :S/W
) connection. If you
switch the rear output setting to
R-SP :S/W
, you can connect a rear speaker lead
directly to a subwoofer without using an auxiliary amp.
Initially, the unit is set for rear full-range speaker connection (
R-SP :FUL
). When rear
output is connected to full range speakers (when
R-SP :FUL
is selected), you can
connect other full range speakers (
P/O :FUL
) or a subwoofer (
P/O :S/W
) to the RCA
rear output.
1. Press FUNCTION to select R-SP.
Press
FUNCTION
repeatedly until
R-SP
appears in the display.
2. Press
8
or
2
to switch the rear output setting.
Pressing
8
or
2
will switch between
R-SP :FUL
(full-range speaker) and
R-SP :S/W
(subwoofer) and that status will be displayed.
•
When no subwoofer is connected to the rear output, select
R-SP :FUL
.
•
When a subwoofer is connected to the rear output, set for subwoofer
R-SP :S/W
.
•
When the rear output setting is
R-SP :S/W
, you cannot operate the following
procedure.
3. Press
4
or
6
to switch the subwoofer output or rear output.
Pressing
4
or
6
will switch between
P/O :S/W
and
P/O :FUL
and that status will be
displayed.
Notes
•
Even if you change this setting, there is no output unless you turn the subwoofer output on
(refer to “Using subwoofer output” on page 26).
•
If you change this setting, subwoofer output in the audio menu return to the factory settings.
Saving the battery consumption
Even when this unit is switched off, the microcomputer inside still uses a small amount
of power in order to enable a quick restart. Switching on the Power Save mode will
prevent the microcomputer from running unnecessarily, thereby saving the battery in
your vehicle.
•
With Power Save mode on, you cannot insert or eject a disc when power to the unit
is off. Press
SOURCE
to switch the unit on, then try again.
Important
If the battery in your vehicle is disconnected the Power Save mode is canceled. Turn
on Power Save again once the battery has been reconnected. If the ignition switch in
your vehicle doesn’t have an ACC (accessory) position, it is possible depending on the
connection method that when Power Save is off, the unit will draw power from the
battery.
1. Press FUNCTION to select SAVE.
2. Press
8
or
2
to turn power save on or off.
MAN-DEH-P4800MP-GB.fm Page 29 Thursday, September 29, 2005 11:55 AM
