61
5
6
7
8
F
E
D
C
B
A
5
6
7
8
DEH-MG8137ZT/UC
Notes:
*1) Insertion/ejection error is output only when door open/close error occurs with forced eject.
*2) LIFT error is output under the following conditions:
LIFTDN --> TLFTUP --> forced eject --> door open/close error
*3) The values of m2stat:
B.upNg=0, FwdTo=1, RevTo=2, Chata=3, OverCnt=4, SwNg=5, SpdNg=6,
Fwd2To=7, Rev2To=8, Sw2Ng=9
*4) The last results of chatter check (compared with the target center):
+8LSB=1, +7LSB=2, +6LSB=3, +5LSB=4, +4LSB=5, +3LSB=6, +2LSB=7,
+1/0LSB=8, -1/0LSB=8,-2LSB=9, -3LSB=a, -4LSB=b, -5LSB=c, -6LSB=d, -7LSB=e, -8LSB=f,
the others=0
*5) Basically the value of eudpzt except for the following case:
In case of eudpzt=1 and door close mode, eudpzt=e
*6) bit0: P_lo1, bit1: P_lo2, bit2: P_elv1, bit3: P_elv2, bit4: P_cg1, bit5: P_cg2,
bit6: P_elv_vol, bit7: P_lod_vol
Claw: It's the part that looks like a claw. It's used to clamp a disc.
CAMRST: Mechanical initialization motion just after resetting
WTLOAD: Loading motion
EJCTON: Ejection motion
SEJPCK: Mechanical motion to check that there is no disc around the loading slot
HLFLOAD: Half loading
DINSRDY: Waiting for disc insertion
LIFTDN: Preparatory motion to clamp a disc after loading
LIFTUP: Preparatory motion to eject a disc
TRAYUP: CAM motor rotation to release the clamped disc from the position where the disc can be rotated
TRYDN: CAM motor rotation to reach the position where the disc can be rotated
CRGOUT: Carriage evacuating motion outside the disc to get ready for elevation motion
CRGIN: Carriage inserting motion inside the disc to get ready for clamping the disc
ELVIN: CAM motor rotation to reach the position where elevation motion can be carried out
ELVOUT: CAM motor rotation to reach the position where disc insertion/ejection can be carried out
EIN_EXP: CAM motor rotation to reach the position where elevation motion can be carried out
CIN_EXP: CAM motor rotation to reach the position where claw's opening/closing motion
DSKFREE: Claw's closing motion to release the clamped disc
DSKLOCK: Claw's opening motion to clamp a disc
CLWCLSE: Claw's closing motion
CLWOPEN: Claw's opening motion
DISCSEL: Elevation motion
FEJCHK: Mechanical motion to check that there is no disc around the loading slot
Summary of Contents for DEH-MG8137ZT
