3
En
English
When mounting spikes on speaker stand
Use only
spikes
,
spike bases
, and
auxiliary feet
provided with
the S-4EX.
1
Install spikes in three locations on the bottom of the
stand base plate, then install the two auxiliary feet to
prevent rocking.
2
Place spike bases on the floor in the position where the
spikes will rest.
3
Rotate the spikes to adjust the height, then rotate the
spike nuts counterclockwise to lock the height of the spike.
4
Rest the speaker stand on the spike bases and check to
confirm the stand is stable without any rocking.
5
Rotate the auxiliary feet to adjust height.
Adjust the height so that about 1 mm to 2 mm of space
remains open between the feet and the installation surface.
6
Rotate the nuts counterclockwise to lock the height.
7
Rest the speaker on the top of the stand and use washers,
spring washers and screws (bind head M5 x L55) to fasten
the speaker securely to the stand.
• When installing spikes, lay the speaker stands on their sides
on a soft blanket or surface to prevent scaring.
• Set the spike bases with the concave side upward to receive
the spike as shown below.
• When the spikes are used alone without spike bases,
scratches may be cuased to the floor or other installation
surface. Always use the spike bases when using spikes.
Other Information
Stand maintenance
• Use a polishing cloth or dry cloth to wipe off dust and dirt.
• If the stand is very dirty, use a soft cloth dipped in some neutral
cleanser diluted five or six times with water. Finally, wipe again
using a dry cloth. Do not use furniture wax or cleaners.
• Never use thinners, benzine, insecticide sprays and other
chemicals on or near the stand, since these will corrode the
surfaces.
Specifications
External dimensions . . . . . . . 360 (W) mm x 570 (H) mm x 485 (D) mm
14
3
/
16
(W) in. x 22
1
/
2
(H) in. x 19
1
/
8
(D) in.
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9 kg (30 lb 11 oz.)
Supplied accessories
Screws (Bind head, M5 x L55) [SBA1307] . . . . . . . . . . . . . . . . . . . . . . 2
Spring washers [SBE6005] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Washers [SBE6006] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Cork plates [SEC2255] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
These operating instructions [SRD6100]
• Specifications and design subject to possible modification
without notice, due to improvements.
• The product number are listed above in square brackets.
Spike
Spike nut
Stand base plate
Auxiliary feet
55 mm
Black
Speaker base
Speaker
support
Screw holes
for securing speaker
Fastening nut
Washer
[SBE6006]
Spring washer
[SBE6005]
Screws
(Bind head, M5xL55)
[SBA1307]
Replacement part numbers
Part name
• Protector (Bottom)
• Protector (Top)
• Packing case
• Protection sheet
Part no.
SHA2632
SHA2631
SHH1324
SHC1879
Published by Pioneer Corporation.
Copyright © 2008 Pioneer Corporation.
All rights reserved.
01_CP-4EX_EN.fm 3 ページ ２００８年７月２４日 木曜日 午後１２時５０分
