Pioneer AVIC-S2 Software Manual Download

Page: 30 / 76

•

Red shows there is a connection, but the signal is too weak to give a

position. GPS navigation is not possible.

•

Blue shows there is a GPS position, and navigation is possible. When only

one arc is shown, the position is 2D (no altitude available), and position error may
be significant, but AVIC-S2 is ready to navigate.

•

A blue satellite and two arcs represent a 3D GPS position. AVIC-S2 is ready

to navigate.

4.3.10

Battery status (No. 12)

The status of the battery is also shown by AVIC-S2. You can estimate the available
power reserve from the length of the bar inside. Some examples:

•

The thunderbolt in the battery shows the battery is connected to external

power and being charged.

•

Battery is not charging, and it is at full capacity.

•

Battery in not full, but there is sufficient reserve capacity.

•

Battery needs recharging.

4.3.11

Sound muting (No. 13)

By tapping this button you can quickly mute all sounds of the device. This will not
modify the volume level and the enabled or disabled status of the key sounds, just
mutes the sound output. When muting is enabled, the speaker icon is crossed out.

Tap again to enable sounds.

Summary of Contents for AVIC-S2













































































Search results

Summary of Contents for AVIC-S2

Reviews:

Related manuals for AVIC-S2

Brands by name

Popular brands

Pioneer AVIC-S2, Software Manual

Search results

Summary of Contents for AVIC-S2

Reviews:

Related manuals for AVIC-S2

Brands by name

Popular brands