3
X:\print\Pioneer\19AJ\HIGH\19_High_UC_QRD3722(A5_Horizon)_INST\020Chapter_EN.fm
AVH-W4500NEX
19_High_UC_QRD3722(A5_Horizon)
En
En
g
lish
(impedance value). Do not use 1 Ω to 3 Ω
speakers for this product.
•
The black lead is ground. When installing
this unit or power amp (sold separately),
make sure to connect the ground wire
first. Ensure that the ground wire is
properly connected to metal parts of the
car’s body. The ground wire of the power
amp and the one of this unit or any other
device must be connected to the car
separately with different screws. If the
screw for the ground wire loosens or falls
out, it could result in fire generation of
smoke or malfunction.
•
When replacing the fuse, be sure to only
use a fuse of the rating prescribed on this
product.
•
When disconnecting a connector, pull the
connector itself. Do not pull the lead, as
you may pull it out of the connector.
•
This product cannot be installed in a
vehicle without ACC (accessory) position
on the ignition switch.
•
To avoid short-circuiting, cover the
disconnected lead with insulating tape. It
is especially important to insulate all
unused speaker leads, which if left
uncovered may cause a short circuit.
•
For connecting a power amp or other
devices to this product, refer to the
manual for the product to be connected.
•
The graphical symbol
placed on
the product means direct current.
•
When the ignition switch is turned on
(ACC ON), a control signal is output
through the blue/white lead. Connect to
an external power amp’s system remote
control terminal, the auto-antenna relay
control terminal, or the antenna booster
power control terminal (max. 300 mA 12
V DC). The control signal is output
through the blue/white lead, even if the
audio source is switched off.
Important
When this product is in [Power OFF] mode,
the control signal is also turned off. If
[Power OFF] mode is canceled, the control
signal is output again and the antenna is
extended with the auto antenna function
(if the antenna is being used). Be careful so
that the extended antenna does not come
into contact with any obstacles.
Ground wire
POWER AMP
Other devices
(Another electronic
device in the car)
Metal parts of car’s
body
*1 Not supplied for this unit
ACC position
No ACC position
Notice for the blue/
white lead
GPS antenna 3.55 m (11 ft. 8 in.)
Microphone 3 m (9 ft. 10-1/8 in.)
iDatalink adapter input
Refer to the instruction manual for the
iDataLink adapter (sold separately).
RGB cable (supplied with Navigation
system)
SiriusXM Connect Vehicle Tuner
Refer to the instruction manual for
SiriusXM Connect Vehicle Tuner (sold
separately).
This product
Pioneer navigation system
Contact your dealer to inquire about
the connectable navigation unit.
Antenna jack
AV cable IN/OUT
Power supply
Fuse (10 A)
Wired remote input
Hard-wired remote control adapter can
be connected (sold separately).
NOTE
Before using and/or connecting the
iDatalink Maestro adapter (sold
separately), you will need to first flash the
Maestro module with the appropriate
vehicle and head unit firmware. You can
find the device number that is required for
the activation on the followings (refer to
the Operation Manual.):
•
The label on the packaging of this
product
•
The label on this product
•
The [Firmware Information] screen
WARNING
IMPROPER CONNECTION MAY RESULT IN
SERIOUS DAMAGE OR INJURY
INCLUDING ELECTRICAL SHOCK, AND
INTERFERENCE WITH THE OPERATION
OF THE VEHICLE'S ANTILOCK BRAKING
SYSTEM, AUTOMATIC TRANSMISSION
AND SPEEDOMETER INDICATION.
To power supply
Power cord
Yellow
To terminal supplied with power
regardless of ignition switch position.
Red
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF
Rear panel (main
terminals)
Power cord