DIN Rear-mount
Installation using the screw holes on
the side of the unit
• Fastening the unit to the factory
radio mounting bracket. (Fig. 17)
(Fig. 18) (Fig. 19)
Select a position where the screw holes
of the bracket and the screw holes of
this product become aligned (are fitted),
and tighten the screws at 2 places on
each side. Use any of binding screws (4
×
3 mm), binding screws (5
×
6 mm) or
flush surface screws (5
×
6 mm),
depending on the shape of the screw
holes in the bracket.
*1 Use binding screws (4
×
3 mm) only.
Fig. 17
• When installing in a shallow space,
use the following screw holes. In this
case, stick conceal tape on parts that
protrude from the dashboard.
Fig. 18
Fig. 19
Fastening the front panel
If you do not plan to detach the front
panel, the front panel can be fastened
with supplied screw. (Fig. 20)
Fig. 20
Fixing screw
Screw
Dashboard or
Console
Factory radio mounting
bracket
*1
*1
Conceal tape
*1
*1
Note:
• Check all connections and systems before final
installation.
• Do not use unauthorized parts. The use of unautho-
rized parts may cause malfunctions.
• Consult with your dealer if installation requires
drilling of holes or other modifications of the vehi-
cle.
• Do not install this unit where:
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result
of a sudden stop.
• Do not install the display where it may (i) obstruct
the driver's vision, (ii) impair the performance of
any of the vehicle's operating systems or safety
features, including air bags, hazard lamp buttons or
(iii) impair the driver's ability to safely operate the
vehicle.
• The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.
• Optimum performance is obtained when the unit is
installed at an angle of less than 30°. (Fig. 12)
Fig. 12
• The cords must not cover up the area shown in the
figure below. This is necessary to allow the ampli-
fires to radiate freely. (Fig. 13)
Fig. 13
DIN Front/Rear-mount
This unit can be properly installed
either from “Front” (conventional DIN
Front-mount) or “Rear” (DIN Rear-
mount installation, utilizing threaded
screw holes at the sides of unit chassis).
For details, refer to the following illus-
trated installation methods.
Before installing the unit
• Remove the frame and the hold-
er. (Fig. 14)
Pull out to remove the frame and then
loosen the screws (2
×
3 mm) to
remove the holder. (When reattaching
the frame, point the side with a groove
downwards and attach it.)
Fig. 14
Holder
Frame
Screw (2
×
3 mm)
Do not close this area.
30
°
DIN Front-mount
Installation with the rubber bush
1. Decide the position of the side
brackets. (Fig. 15)
When installing in a shallow space,
change the position of side brackets. In
this case, stick conceal tape on parts
that protrude from the dashboard.
Fig. 15
2. Install the unit into the dash-
board. (Fig. 16)
After inserting the holder into the dash-
board, then select the appropriate tabs
according to the thickness of the dash-
board material and bend them.
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
• After installing the unit into the dash-
board, reattach the frame.
Fig. 16
Rubber bush
Screw
Dashboard
Side bracket
Screw (2
×
3 mm)
182
53
Holder
Conceal tape
Side bracket
Flush surface screw (5
×
6 mm)
Connecting the Units
ENGLISH
When connecting the external video component and the display
Fig. 11
• It is necessary to set
AV INPUT
to
VIDEO
in
SET UP
when connecting the external
video component.
• It is necessary to set
AV INPUT
to
M-DVD
in
SET UP
when connecting a multi-DVD
player.
When using a display connected to rear video output
This product’s rear video output is for connection of a display to enable passengers in the
rear seats to watch the DVD or Video CD.
WARNING:
• NEVER install the display in a location that enables the Driver to watch the DVD or Video CD while
Driving.
To video output
video
RCA cables
(sold separately)
To audio outputs
Display with
RCA input jacks
To video input
Video output
Audio input
Video input
RCA cable
(sold separately)
Audio output
External
component
(sold separately)
Multi-DVD Player
(sold separately)
Video output
Installation
ENGLISH
