background image

3

En
g

lis

h

(Maximum input power) and between 4 
Ω to 8 Ω (impedance value).  Do not use 1 
Ω to 3 Ω speakers for this unit.

When rear speaker output is used by 2 Ω
of subwoofer, use speakers over 70 W 
(Maximum input power).
*Please refer to connection for a 
connection method.

The black cable is ground. When 
installing this unit or power amp (sold 
separately), make sure to connect the 
ground wire first. Ensure that the ground 
wire is properly connected to metal parts 
of the car’s body. The ground wire of the 
power amp and the one of this unit or 
any other device must be connected to 
the car separately with different screws. If 
the screw for the ground wire loosens or 
falls out, it could result in fire generation 
of smoke or malfunction.

When replacing the fuse, be sure to only 
use a fuse of the rating prescribed on this 
product.

This product cannot be installed in a 
vehicle without ACC (accessory) position 
on the ignition switch.

To avoid short-circuiting, cover the 
disconnected lead with insulating tape. It 
is especially important to insulate all 
unused speaker leads, which if left 
uncovered may cause a short circuit.

For connecting a power amp or other 
devices to this product, refer to the 
manual for the product to be connected.

The graphical symbol 

 placed on 

the product means direct current.

When the ignition switch is turned on 
(ACC ON), a control signal is output 
through the blue/white lead. Connect to 
an external power amp’s system remote 
control terminal, the auto-antenna relay 
control terminal, or the antenna booster 
power control terminal (max. 300 mA 12 
V DC). The control signal is output 
through the blue/white lead, even if the 
audio source is switched off.

Ground wire

POWER AMP

Other devices 
(Another electronic 
device in the car)

Metal parts of car’s 
body

*1 Non supplied for this unit

Notice for the blue/
white lead

ACC position

No ACC position

 Microphone 3 m (9 ft. 10-1/8 in.)
 Wired remote input

Hard-wired remote control adapter can 
be connected (sold separately).

 SiriusXM Connect Vehicle Tuner

Refer to the instruction manual for 
SiriusXM Connect Vehicle Tuner (sold 
separately).

 RGB cable (supplied with Navigation 

system)

 This product
 Pioneer navigation system

Contact your dealer to inquire about 
the connectable navigation unit.

 Antenna jack
 Subwoofer output (STD)/Low range 

output (NW)

 Rear output (STD)/Middle range output 

(NW)

 Front output (STD)/High range output 

(NW)

 Power supply
 Fuse (10 A)
 iDatalink adapter input

NOTE

Before using and/or connecting the 
iDatalink Maestro adapter, you will need to 
first flash the Maestro module with the 
appropriate vehicle and head unit 
firmware. You can find the device number 

that is required for the activation on the 
followings (refer to the Operation Manual.):

The label on the packaging of this 
product

The label on this product

The [Firmware Information] screen

 To power supply
 Power cord
 Yellow

To terminal supplied with power 
regardless of ignition switch position.

 Red

To electric terminal controlled by 
ignition switch (12 V DC) ON/OFF

 Orange/white

To lighting switch terminal.

 Black (ground)

To vehicle (metal) body.

 Violet/white

Of the two lead wires connected to the 
back lamp, connect the one in which 
the voltage changes when the gear shift 
is in the REVERSE (R) position. This 
connection enables the unit to sense 

This product

Power cord

Summary of Contents for AVH-601EX








Reviews: