Operation
04
11
En
English
Deutsch
Français
Nederlands
Italiano
Español
Ру
сский
Chapter 4:
Operation
Playback
1
Turn on the power of the playback
component.
2
Turn power ON to the unit.
• If the unit is in the standby mode, press the remote
control’s
STANDBY/ON
button.
3
Select the source you want to playback.
Select the playback component.
• When using the front panel controls, rotate the
INPUT SELECTOR
knob.
• In the case of the A-70DA, if
PHONO
is selected,
use the
CARTRIDGE
select switch to designate the
type of cartridge used with your turntable, either
MM (
) or MC (
).
4
Start playback of the component you
selected in step 1.
5
Adjust playback volume with VOLUME
control.
6
Adjust the tone to your preference using
the BASS and TREBLE controls, and
LOUDNESS button.
If the
DIRECT
button has been set to ON, these controls
are disabled.
3
5
6
6
6
2
MENU
iPod
Music>
Extras>
Settings>
Shuffle Songs
Backlight
SOURCE
/I STANDBY/ON
STANDBY
iPod/iPhone
5V
1A
DIRECT
Hi-Bit 32
Up Sampling
SOURCE
SACD/CD player
Network audio player
Turntable
iPod dock, etc.
Recording device
or other device
Playback
Playback
Audio device with
balanced output terminals
VOLUME
Caution
• The
BASS
,
TREBLE
,
BALANCE
, and
LOUDNESS
functions do not work for a device connected to the
BALANCED
IN
terminals.
Set the power to Standby
1
Press the remote control’s
STANDBY/
ON button.
The next time you wish to turn on the power, press the
remote control’s
STANDBY/ON
button.
• If the front panel’s
/I STANDBY/ON
button is
pressed, the power will be turned off. In this case, if
the power is off, pressing the remote control’s
STANDBY/ON
button will not turn on the power.
To turn on the power again, press the front panel’s
/I STANDBY/ON
button.
When using the unit as a power amplifier
When a pre-amplifier is connected to the unit’s
POWER
AMP DIRECT
IN
terminals, the unit can be used as a
power amplifier.
1
Press the POWER AMP DIRECT button
on the remote control or front panel of the
unit.
The
POWER AMP DIRECT
indicator will light.
Caution
• When the
POWER AMP DIRECT
indicator is
lighted, operations change as follows:
– The unit’s front-panel
VOLUME
,
BASS
,
TREBLE
,
and
BALANCE
controls are disabled. These
adjustments are controlled by the component
connected to the unit’s
POWER AMP DIRECT
IN
terminals.
– The
LOUDNESS
button and
ATTENUATOR
button (A-70DA only) are disabled.
– When the
POWER AMP DIRECT
indicator is
lighted, sound volume from the unit will
automatically be fixed at its maximum output.
When using this unit as a power amplifier,
check the output level of the component
connected to the
POWER AMP DIRECT
IN
terminals and set it to a low level as appropriate
before turning on the
POWER AMP DIRECT
indicator. If the sound volume of the component
connected to the
POWER AMP DIRECT
IN
terminals is initially set to a high output level,
loud sound may suddenly be output when the
POWER AMP DIRECT
indicator lights.
– Sound is not produced from the
PHONES
jack
and
LINE 2 OUT
terminals.
• For more information, consult the operating
instructions for the component connected to the
unit’s
POWER AMP DIRECT
IN
terminals.
Playing music from a digital audio
component
Output the digital audio input to the
DIGITAL IN
COAXIAL
or
OPTICAL
terminal.
1
Make a digital input connection.
• See
Digital audio input connections
on page 7.
2
Switch to the COAXIAL or OPTICAL
input.
Each press of the
COAXIAL/OPTICAL
button on the
remote control switches the input alternately.
• When using the front panel controls, rotate the
INPUT SELECTOR
knob.
• Sound is produced from the
LINE 2 OUT
terminals.
Note
• Digital signal formats that can be input to this unit
include linear PCM signals with sampling rates and
quantitative bits up to 192 kHz/32 bits (Depending
on the connected device and environment,
operation may not be successful).
A70_SYXE8_0728.book 11 ページ ２０１５年７月２８日 火曜日 午後３時５４分
