Pima SAT-9 Installation And Programming Manual Download Page 12

12 

SAT-9/TD-900 Installation and Programming Guide 

 
 

4.

 

MAINTENANCE 

Follow these steps in order to remove the SAT-9 from TD-900 for maintenance operations 

and transmitter programming: 

1.

 

Open the TD-900 box and locate the SAT-9 (see ‎Figure 4  on page 6) 

2.

 

Disconnect the power cords from the SAT-9 

3.

 

Remove the SAT-9 antenna 

4.

 

Remove the two screws (B1 & B2) holding the SAT-9 in the box and gently 
remove the SAT-9 (see ‎Figure 4 on page 6) 

To reassemble the TD-900, simply follow the above steps in reverse order. 
 

Limited Warranty 

PIMA Electronic Systems Ltd. does not represent that its product may not be compromised and/or  circumvented, 
or that the Product will prevent any death, personal and/or bodily injury and/or damage to property resulting from 
burglary, robbery, fire or otherwise, or that the Product will in all cases provide adequate warning or protection.  
The User understands that a properly installed and maintained equipment may only reduce the risk of events such 
as burglary, robbery, and  fire without warning,  but  it  is  not  insurance or a  guarantee that such will  not occur  or 
that there will be no death, personal damage and/or damage to property as a result. 

PIMA Electronic  Systems Ltd. shall  have  no liability for any death,  personal and/or  bodily injury and/or 
damage to property or other loss whether direct, indirect, incidental, consequential or otherwise, based on 
a claim that the Product failed to function. 

Please refer to a separate warranty statement found on PIMA website at:  

http://www.pima-alarms.com/site/Content/t1.asp?pid=472&sid=57

 

This document may not be duplicated, circulated, altered, modified, translated, reduced to any form or otherwise 
changed; unless PIMA’s prior written consent is granted. 

All efforts have been made to ensure that the content of this manual is accurate.  Pima retains the right to modify 
this manual or any part thereof, from time to time, without serving any prior notice of such modification. 

Copyright 

 2012 PIMA Electronic Systems Ltd.  All rights reserved. 

 
 

PIMA Electronic Systems Ltd.,  
5 Hatzoref Street 
Holon 58856, ISRAEL 
Tel: +972.3.6506414 
Fax: +972.3.5500442 
Email: 

[email protected]

 

Web: 

http://www.pima-alarms.com

 

 
 

4410141  

*4410141*

 

Ver: B, XX en (Aug 2012) 

Summary of Contents for SAT-9













Reviews: