background image

Contents

Operating Manual PSEN 2.1b-26
21380-EN-12

| 3

Introduction 

............................................................................................................................

4

Validity of documentation

..........................................................................................................

4

Using the documentation

..........................................................................................................

4

Definition of symbols

.................................................................................................................

4

Safety 

......................................................................................................................................

5

Intended use

.............................................................................................................................

5

Safety regulations

.....................................................................................................................

6

Safety assessment

...................................................................................................................

6

Use of qualified personnel

........................................................................................................

6

Warranty and liability

................................................................................................................

6

Disposal

....................................................................................................................................

6

For your safety

..........................................................................................................................

7

Unit features 

...........................................................................................................................

7

Function description 

.............................................................................................................

7

Block diagram

...........................................................................................................................

8

Operating distances

..................................................................................................................

8

Lateral and vertical offset

..........................................................................................................

9

Wiring 

......................................................................................................................................

9

Pin assignment

.........................................................................................................................

10

Requirements and connection to evaluation devices 

........................................................

10

Installation 

..............................................................................................................................

13

Adjustment 

.............................................................................................................................

15

ATEX installation and operating regulations (X) 

................................................................

15

Periodic test 

...........................................................................................................................

16

Dimensions in mm 

.................................................................................................................

16

Technical details 

....................................................................................................................

17

Safety characteristic data

.........................................................................................................

18

Order reference 

......................................................................................................................

19

System

......................................................................................................................................

19

Accessories

..............................................................................................................................

19

EC declaration of conformity 

................................................................................................

19

Summary of Contents for PSEN 2.1b-26






















Reviews: