background image

Introduction

This user manual will cover the 12 and 24v version of both the Pilot Gas 
Monitoring System and the Twin Channel Gas Alarm.

The Pilot range of gas monitoring alarms are important and cost effective 
items of safety equipment wherever LPG may be present.

However good a gas installation may be, there is always a chance that a 
potentially lethal leak may occur. Vapours present on boats such as 

butane, propane and petrol vapour are heavier than air. Even a small leak 
can build up to dangerous proportions in the bilges of a boat.

Gas Monitoring System

The Gas Monitoring System (GMS) is designed to work with two LPG 

sensors. This allows a greater coverage of gas detection for your boat. 
The GMS is also supplied with a solenoid valve which is installed in your 

gas supply. Your gas supply will then be controlled by the GMS which has 
a button to open/close the valve. In the event of an alarm, the GMS will 

automatically close the valve to switch off the gas supply. 

Twin Channel Gas Alarm

The Twin Channel Gas Alarm is supplied with two sensors. It has all of the 
features of the Gas Monitoring System, however, is not compatible with 

the solenoid gas valve.

A Gas Valve Controller may be purchased as an add-on to convert a Twin 

Channel Gas Alarm into a Gas Monitoring System.

User manuals for the full range of Pilot products are available in PDF 

format on the Envin Scientific website – 

www.envinsci.co.uk

1

Summary of Contents for 2011112/716/12
















Reviews: