manualshive.com logo in svg

PIE PIECAL 541, Operating Instructions Manual

Share
Download
PIE PIECAL 541 Operating Instructions Manual Download Page 8

Additional Information 

This product is calibrated on equipment traceable to NIST and includes a Certificate of Calibration. 

Test Data is available for an additional charge.

Practical Instrument Electronics recommends a calibration interval of one year. Contact your local 

representative for recalibration and repair services.

Warranty

Our equipment is warranted against defective material and workmanship (excluding batteries) for a 
period of three years from the date of shipment. Claims under warranty can be made by returning 
the equipment prepaid to our factory. The equipment will be repaired, replaced or adjusted at our 
option. The liability of Practical Instrument Electronics (PIE) is restricted to that given under our 
warranty. No responsibility is accepted for damage, loss or other expense incurred through sale or 
use of our equipment. Under no condition shall Practical Instrument Electronics, Inc. be liable for any 
special, incidental or consequential damage.

 

 

 

 

 

 

 

 

 

    

Page 8

Accessories

Included: 

“9V” Alkaline battery, Certificate of Calibration

Large Carrying Case with PIE Logo 

  Part No. 020-0204

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

 TestEquipmentDepot.com 

Summary of Contents for PIECAL 541









Reviews:

No comments

Brands by name

Popular brands

Load more brands