Pico Technology
Quick Start Guide
DO210-9
3
3.
Battery replacement
1. Place the NVH Interface face down and remove the four securing screws.
2. Remove the base cover from the NVH Interface.
3. Lift the old battery away from the connections.
4. Place the new battery in position. Make sure it has
the correct orientation.
5. Replace the base cover and secure it.
4.
Connections
1. Connect the oscilloscope to your computer with the blue
USB cable supplied with the oscilloscope.
2. Connect the NVH Interface box to the PicoScope with the supplied BNC cables.
You will require one BNC cable when you use a microphone and up to three when
you use an accelerometer.
3. Connect either the microphone (a) or the accelerometer (b) to the NVH Interface.
Note: The extension cable provided may be used to extend the reach of either the
microphone or the accelerometer.
4. Run the PicoDiagnostics software.
5.
NVH Magnet mounting instructions
1. 'LIGOXLEXXLIQSYRXMRKWYVJEGIJSVIEGLQEKRIXMWƽEXERHJVIIJVSQ
contamination.
2. Slide the keeper off the mounting magnet(s).
3. Mount the magnet/sensor assembly to the prepared test surface by gently rolling
it into place. This will avoid damaging the surface.
Note: ;MXLERSRQIXEPPMGWYVJEGIWYGLEWEPPS]WYFJVEQIWMXQE]FITSWWMPFPIXSƼ\E
small steel disk to the chassis with cyanoacrelate glue that you can use as a mounting
location.
3 Channel
NVH
In
ter
face
X
Y
Z
(a)
3 Channel
NVH
In
ter
face
X
Y
Z
T
A143
Y
X
Z
(b)
PicoDiagnostics NVH interface
Pico Technology
2
DO210-9
1.
Introduction
Thank you for buying a PicoDiagnostics NVH Kit. This Quick Start Guide will help you set
up your NVH Interface(s) and your PicoScope Automotive Oscilloscope. In conjunction
with this guide, please also see the NVH help within the PicoDiagnostics software.
2.
Safety warnings
Please review the following safety precautions to avoid injury and prevent damage to
your NVH equipment.
%;%62-2+MHIRXMƼIWGSRHMXMSRWSVTVEGXMGIWXLEXGSYPHVIWYPXMRMRNYV]SVHIEXL
%'%98-32MHIRXMƼIWGSRHMXMSRWSVTVEGXMGIWXLEXGSYPHVIWYPXMRHEQEKIXSXLITVSHYGX
or equipment to which it is connected.
WARNING
WARNING
7XVSRKQEKRIXMGƼIPHWQE]EJJIGXSVHMWEFPIXLISTIVEXMSRSJTEGIQEOIVW
ICDs and other implanted medical devices. To avoid injury or death do not
YWIXLMWTVSHYGXMJ]SYSVSXLIVTISTPIRIEVF]EVIƼXXIH[MXLWYGLHIZMGIW
The magnet can attract metallic objects or other magnets from large
distances, causing trapping injuries unless care is taken when handling.
WARNING
To avoid an accident do not operate PicoDiagnostics or the kit while driving
the vehicle. Take a passenger with you to operate the software.
CAUTION
To prevent damage or measurement errors make sure that you only use
WIRWSVWETTVSZIHF]4MGSɸ8IGLRSPSK][MXLXLMWYRMX
To avoid entrapment take care to route any cables away from moving parts
when you use the propshaft balancing accessories.
To avoid melting of cables take care to route them away from hot engine
components when you use this product.
In order to protect the NVH magnet as well as nearby objects, make sure that
XLIOIITIVMWƼXXIHXSXLIQEKRIX[LIRMXMWWXSVIHSVMRXVERWMX
To conserve battery life do not store the NVH interface with a sensor
connected. The interface is powered on whenever the sensor is connected.
Do not apply a voltage to the BNC or sensor connectors on the NVH
interface. The BNC connectors are outputs only.
7XVSRKQEKRIXMGƼIPHWGERHEQEKIWIRWMXMZIIPIGXVSRMGHIZMGIWERH
magnetic material such as credit cards or portable storage media.
Your help and efforts are required to protect and keep our environment clean.
Therefore either return these product at the end of life to the manufacturer or
ensure WEEE compliant collection and treatment yourself. Do not dispose of
as unsorted municipal waste.
Pico Technology
Quick Start Guide
DO210-9
3
3.
Battery replacement
1. Place the NVH Interface face down and remove the four securing screws.
2. Remove the base cover from the NVH Interface.
3. Lift the old battery away from the connections.
4. Place the new battery in position. Make sure it has
the correct orientation.
5. Replace the base cover and secure it.
4.
Connections
1. Connect the oscilloscope to your computer with the blue
USB cable supplied with the oscilloscope.
2. Connect the NVH Interface box to the PicoScope with the supplied BNC cables.
You will require one BNC cable when you use a microphone and up to three when
you use an accelerometer.
3. Connect either the microphone (a) or the accelerometer (b) to the NVH Interface.
Note: The extension cable provided may be used to extend the reach of either the
microphone or the accelerometer.
4. Run the PicoDiagnostics software.
5.
NVH Magnet mounting instructions
1. 'LIGOXLEXXLIQSYRXMRKWYVJEGIJSVIEGLQEKRIXMWƽEXERHJVIIJVSQ
contamination.
2. Slide the keeper off the mounting magnet(s).
3. Mount the magnet/sensor assembly to the prepared test surface by gently rolling
it into place. This will avoid damaging the surface.
Note: ;MXLERSRQIXEPPMGWYVJEGIWYGLEWEPPS]WYFJVEQIWMXQE]FITSWWMPFPIXSƼ\E
small steel disk to the chassis with cyanoacrelate glue that you can use as a mounting
location.
3 Channel
NVH
In
ter
face
X
Y
Z
(a)
3 Channel
NVH
In
ter
face
X
Y
Z
T
A143
Y
X
Z
(b)
PicoDiagnostics NVH interface
Pico Technology
2
DO210-9
1.
Introduction
Thank you for buying a PicoDiagnostics NVH Kit. This Quick Start Guide will help you set
up your NVH Interface(s) and your PicoScope Automotive Oscilloscope. In conjunction
with this guide, please also see the NVH help within the PicoDiagnostics software.
2.
Safety warnings
Please review the following safety precautions to avoid injury and prevent damage to
your NVH equipment.
%;%62-2+MHIRXMƼIWGSRHMXMSRWSVTVEGXMGIWXLEXGSYPHVIWYPXMRMRNYV]SVHIEXL
%'%98-32MHIRXMƼIWGSRHMXMSRWSVTVEGXMGIWXLEXGSYPHVIWYPXMRHEQEKIXSXLITVSHYGX
or equipment to which it is connected.
WARNING
WARNING
7XVSRKQEKRIXMGƼIPHWQE]EJJIGXSVHMWEFPIXLISTIVEXMSRSJTEGIQEOIVW
ICDs and other implanted medical devices. To avoid injury or death do not
YWIXLMWTVSHYGXMJ]SYSVSXLIVTISTPIRIEVF]EVIƼXXIH[MXLWYGLHIZMGIW
The magnet can attract metallic objects or other magnets from large
distances, causing trapping injuries unless care is taken when handling.
WARNING
To avoid an accident do not operate PicoDiagnostics or the kit while driving
the vehicle. Take a passenger with you to operate the software.
CAUTION
To prevent damage or measurement errors make sure that you only use
WIRWSVWETTVSZIHF]4MGSɸ8IGLRSPSK][MXLXLMWYRMX
To avoid entrapment take care to route any cables away from moving parts
when you use the propshaft balancing accessories.
To avoid melting of cables take care to route them away from hot engine
components when you use this product.
In order to protect the NVH magnet as well as nearby objects, make sure that
XLIOIITIVMWƼXXIHXSXLIQEKRIX[LIRMXMWWXSVIHSVMRXVERWMX
To conserve battery life do not store the NVH interface with a sensor
connected. The interface is powered on whenever the sensor is connected.
Do not apply a voltage to the BNC or sensor connectors on the NVH
interface. The BNC connectors are outputs only.
7XVSRKQEKRIXMGƼIPHWGERHEQEKIWIRWMXMZIIPIGXVSRMGHIZMGIWERH
magnetic material such as credit cards or portable storage media.
Your help and efforts are required to protect and keep our environment clean.
Therefore either return these product at the end of life to the manufacturer or
ensure WEEE compliant collection and treatment yourself. Do not dispose of
as unsorted municipal waste.
DO347
