background image

-1-

PKI-0072-4

 S-RF Series 

Installation Instructions

Please read the cautionary points before installation to ensure safe utilization of the product.

 The lamp and  the switch harness are intended for motorized vehicle use only. Do not use for any other purpose.

 This lamp is intended for use in rain (day or night), during foggy or snowy conditions where visibility is hampered. 

 

Do not use during normal driving conditions.

 Do not operate the switch while driving, unless local laws allow you to do so.

 If the lamp is kept on when the engine is not running, it will drain the battery.

 Make sure the lamp is installed securely before driving the vehicle. If a problem is found, fi x it immediately.

 Check for any loose screws that hold the lamp in place before driving. If you fi nd any loose screws or bolts (if a bracket is 

 

used), tighten them securely. If you notice a loose part while driving, inspect the section immediately and make the 

 necessary 

adjustments.

 Avoid repeatedly turning the lamp off  and on as it may reduce the overall life of the LED.

 Some vehicles produce a high voltage electric charge when the engine is started. Avoid loading extra voltage to lamps by

 

turning the switch off  when you start engine.

 Avoid needless disassembly of the lamp or the switch harness as it may cause it to fail.

 If the lamp and/or the switch harness is removed and set aside for safekeeping, wipe away all dust or grime and store in a

 

place free of moisture.

 If the lens is cracked or damaged in any way, verify whether there is any damage to the harness. If there is any damage to 

 

the cord covering, replace it immediately.

 Avoid injury when replacing the harness and the switch Please dispose of it as a non-combustible item.

The 

 marks indicated in this manual are cautionary points related to the installation of the product. 

To ensure safe and secure installation of the product, please follow these points closely.

 

To user 

…  Please keep this manual and a receipt with the name of the shop where 

 

 

 

you bought it. When giving this product to a third party, always include 

 

 

 

this manual together with the product.

  To shop owners installing the product  …  After installation of the product, make sure the customer is provided 

 

 

 

with this owner's manual.

 The lamp becomes hot when turned on. When parking your car near fl ammable items such as dried leaves, turn off  the 

 

lamp as it may cause a fi re.

 Do not look directly into the light for long periods. Doing so may cause eye irritation or visual impairment.

Thank you very much for purchasing PIAA product.  Please read this instruction manual 

thoroughly for proper use of the product.  After completing your installation, keep this 

manual for future reference.

Summary of Contents for S-RF Series









Reviews: