background image

PI2Embedded 502V2S

 Hardware Reference Manual – P2.1 - 6/3/2016 

PAGE 3 

1111

 

WARRANTY

WARRANTY

WARRANTY

WARRANTY    

The enclosed product ("the Product"), a part of the PI2MEDIA Shield/Hat series, is 
warranted by Pi 2 Design for a period of one year for reasonable development, testing 
and use, all as further described and defined below.  This warranty runs solely to the 
individual or entity purchasing the Product and is not transferable or assignable in any 
respect.  This warranty is valid only for so long as the product is used intact as shipped 
from PI 2 Design.  Any attempt or effort to alter the Product, including but not limited to 
any attempt to solder, de-solder, unplug, replace, add or affix any part or component of 
or onto the Product, other than components specifically intended for the user to plug 
and unplug into appropriate sockets and/or Connectors to facilitate user programming, 
development and deployment, all as specifically described and authorized in this 
Product Hardware Reference Manual, shall void this warranty in all respects.  Coverage 
under this warranty requires that the Product be used and stored at all times in 
conditions with proper electrostatic protection necessary and appropriate for a complex 
electronic device.  These conditions include proper temperature, humidity, radiation, 
atmosphere and voltage (standard commercial environment, 0C to +70C, <60%RH).  
Any Product that has been modified without the express, prior written consent of Pi 2 
Design is not covered by this warranty.  The use or connection of any test or bus 
Connector, adapter or component with any device other than a Pi 2 Design Connector 
or adapter shall void this warranty and the warranty of all other components, parts and 
modules connected to the rest of the system.  Pi 2 Design shall not be responsible for 
any damage to the Product as a result of a customer's use or application of circuitry not 
developed or approved by Pi 2 Design for use on or in connection with the Product. 

 

This warranty does not cover defects caused by electrical or temperature fluctuations or 
from stress resulting from or caused by abuse, misuse or misapplication of the Product.  
Any evidence of tampering with the serial number on the Product shall immediately void 
this warranty.  This Product is not intended to be used on or embedded in or otherwise 
used in connection with any life-sustaining or life-saving product and this warranty is not 
applicable nor is Pi 2 Design liable in any respect if the Product is so used.  
Notwithstanding anything to the contrary herein, Pi 2 Design expressly disclaims any 
implied warranty of merchantability or implied warranty of fitness for a particular purpose 
in connection with the manufacture or use of the Product. 

Summary of Contents for 502V2S





















Reviews: