background image

TOOLS AND SUPPLIES NEEDED.

•  Medium C/A glue

•  30 minute epoxy

•  6 minute epoxy

•  Hand or electric drill

•  Assorted drill bits

•  Modeling knife

•  Straight edge ruler

•  2 bender plier

•  Wire cutters

•  Masking tape

•  Thread lock

•  Paper towels

•  Rubbing alcohol

SUGGESTION 

To avoid scratching your new airplane, do not unwrap 

the pieces until they are needed for assembly. Cover 

your  workbench  with  an  old  towel  or  brown  paper, 

both  to  protect  the  aircraft  and  to  protect  the  table. 

Keep  a  couple  of  jars  or  bowls  handy  to  hold  the 

small parts after you open the bag.

NOTE:

Please trial fit all the parts. Make sure you have the 

correct parts and that they fit and are aligned properly 

before gluing! This will assure proper assembly. The 

YAK54    MK2  GP/EP  size.120/20cc  SCALE  1:4  ¾ 

ARF  is  hand  made  from  natural  materials,  every 

plane is unique and minor adjustments may have to 

be  made.  However,  you  should  find  the  fit  superior 

and assembly simple.
The painted and plastic parts used in this kit are fuel 

proof. However, they are not tolerant of many harsh 

chemicals  including  the  following:  paint  thinner,  C/A 

glue accelerator, C/A glue debonder and acetone. Do 

not  let  these  chemicals  come  in  contact  with  the 

colors on the covering and the plastic parts.

SAFETY PRECAUTION:

•  This is not a toy

•  Be sure that no other flyers are using your radio 

frequency.

•  Do not smoke near fuel

•  Store  fuel  in  a  cool,  dry  place,  away  from 

children and pets.

•  Wear safety glasses.

•  The glow plug clip must be securely attached to 

the glow plug.

•  Do not flip the propeller with your fingers.

•  Keep loose clothing and wires away from the propeller.

•  Do not start the engine if people are near. Do not 

stand in line with the side of the propeller.

•  Make engine adjustments from behind the propeller 

only. Do not reach around the spinning propeller.

PREPARATIONS

Use  a  covering  iron  with  a  covering  sock  on 

high  heat  to  tighten  the  covering  if  necessary. 

Apply  pressure  over  sheeted  areas  to 

thoroughly bond the covering to the wood.

INSTALLING THE AILERONS AND Flaps

1.  Test fit the ailerons to the wing with the hinges. 

If the hinges don’t remain centered, stick a pin 

through  the  middle  of  the  hinge  to  hold  it  in 

position.

TEMPORARY PIN

TO KEEP HINGE

CENTERED

2.  Apply six drops of thin CA to the top and bottom 

of each hinge. Do not use CA accelerator. After 

the  CA  has  fully  hardened,  test  the  hinges  by 

pulling on the aileron.

1

YAK54  MK2

Instruction Manual

< Bottom view >

Main Wing

Aileron

Summary of Contents for YAK54 MK2

























Reviews: