Philips SD-4.00SA CH, Service Manual

Page: 27 / 65

Test Instructions Mono Board DVD-SD4.00SA_CH EN 27 SD-4.00SA_CH 5.
4 NVRAM Modify [36]
5 NVRAM Read/Wr Test [15]
MAIN > MISCELLANEOUS > STATISTICS INFO MENU
1
Total Nr Of Times Tray Open [47a]
2 Total Time Power On [47b]
3 Total Play-Time CDDA & VCD [47c]
4 Total Play-Time DVD [47d]
Third Level Submenus
MAIN > AUDIO > EXT DAC BOARD > I2C TEST MENU
1.
I2C Test [66a]
2. I2C Enable Pin On [66b]
3. I2C Enable Pin Off [66c]
MAIN > AUDIO > EXT DAC BOARD > CLOCK MENU
1.
Clock Internal [67a]
2. Clock External [67b]
3. Clock Upsampling 192k (963 only) [82a]
4. Clock Upsampling 96k (963 only) [82b]
5. Clock Upsampling On (963 only) [82c]
6. Clock Upsampling Off (963 only) [82d]
MAIN > AUDIO > EXT DAC BOARD > AUDIO
1.
Audio Pre-Mute On [68a]
2. Audio Pre-Mute Off [68b]
3. Audio Center On [69a]
4. Audio Center Off [69b]
MAIN > AUDIO > EXT DAC BOARD > LOW POWER
STANDBY
1.
Low Power Standby On [81a]
2. Low Power Standby Off [81b]
MAIN > AUDIO > EXT DAC BOARD > DAC MODE MENU
1.
DAC CDDA Mode [80a]
2. DAC DVD48 Mode [80b]
3. DAC DVD96 Mode [80c]
4. DAC DSD Mode [80d
MAIN > BASIC ENGINE > MECHANISM > DISC MOTOR
MENU
1
Disc Motor On [39a]
2 Disc Motor Off [39b]
MAIN > BASIC ENGINE > MECHANISM > LASER MENU
1
CD Laser On [58a]
2 CD Laser Off [58b]
3 DVD Laser On [58c]
4 DVD Laser Off [58d]
MAIN > BASIC ENGINE > MECHANISM > TRAY MENU
1
Tray Open [43b]
2 Tray Close [43a]
MAIN > BASIC ENGINE > MECHANISM > FOCUS MENU
1
Focus On [38a] (load DVD first)
2 Focus Off [38b]
MAIN > BASIC ENGINE > MECHANISM > RADIAL MENU
1
Radial Control On [40a] (load DVD first)
2 Radial Control Off [40b]
MAIN > BASIC ENGINE > MECHANISM > SLEDGE MENU
1
Sledge Inwards [41a]
2 Sledge Outwards [41b]
MAIN > BASIC ENGINE > MECHANISM > GROOVES (Uses
DVD) MENU
1
Jump To Inside Grooves [42a]
2 Jump To Middle Grooves [42b]
3 Jump To Outside Grooves [42c]
Screen Layout With Menus
When menus are used, no specific screen layout can be given:
menu information will not be in a special format, except for the
layout as mentioned in the previous paragraphs.
A typical menu session can look as follows:
Figure 5-42
Depending on the height of the screen, the text will start
scrolling off the top of the screen.
Layout Of Results Diagnostic Nuclei On Control/service Pc
Results returned from a Diagnostic Nucleus to the control/
service PC will have a maximum length of 300 characters and
are terminated by a CR character (included in the string length)
The result has the following layout
< number >< string > [OK l ER] @< CR >
The use of the "@" enables the Asterix system on the Control
PC to parse the output string of each nucleus into a database.
< number > is a 4-digit decimal number padded with leading
zeros if its value is less than 4 digits. The first two digits identify
the generating nucleus (or goup of nuclei), the latter two digits
indicate the error number.
< string > is a text string containing information about the result
of the Diagnostic Nucleus.
< number > and < string > are defined in [SDD_DN] in the
output sections of each Nucleus.
Examples:
CL 26532053_047.eps
240502
DVDv4 Diagnostic Software version 5.03
SDRAM Interconnection test passed
Basic SDRAM test passed
Slave Processor: SLAVE2
(M)enu, (C)ommand or (S)2B interface ? [M]:@ <enter>
Press ENTER to go to main menu
CC: > <enter>
MAIN MENU
1. Audio ...
2. Video ...
3. Front Panel ...
4. Basic Engine ...
5. Processor Peripherals ...
7. Furore ...
8. Miscellaneous ...
Select > 4 <enter>
MAIN > BASIC ENGINE MENU
1. Reset [44]
2. Version [37]
3. S2B
4. Loader Mechanism ...
5. Special Diagnostics ...
Press Enter to go to Main Menu
Select > 5 <enter>
MAIN > BASIC ENGINE > SPECIAL DIAGNOSTIC MENU
1. Read flashID [70]
2. ROM checksum [71]
3. Scratsh detector test [72]
Press Enter to go to Main Menu
CL 16532163_045.eps
230102
4. Device ID: 0x01
Manufac ID: 0xC2
7000 OK @
1. 0001 Unknown command ER @
2. 3100 OK @
3. 0901 Data line X is not connected to the DRAM ER @