background image

3.1.2 Surge 

Immunity 

(Lightning 

Test) 

 
The product shall withstand mains interference’s of: 
 
Differential mode: 

 

2kV/2 ohm criteria C for Europe. 

 

6kV/12 ohm criteria C for NAFTA. 

Parameters: 

 Bi-wave 
 Open 

circuit 

voltage: 

2/50us 

 Short 

circuit 

current: 

8/20us 

 

From +/1kV to +/-2kV (for Europe) or +/-6kV (for Nafta) in steps of 1kV. 

 

10 shots per combination. 

 

One shot per minute. 

 

Serial impedance: 2 Ohm for Europe, 12Ohm for Nafta. 

 

Polarity and phase: Positive (phase 90º) & Negative (phase 270º) 

Technical Specification and Connection Facilities

1-6

 
Common mode: 

 

6kV/2 ohm criteria C for Europe. 

 

6kV/12 ohm criteria C for Nafta. 

Parameters: 

 Ring-wave 

(100kHz) 

 

From +/3kV to +/-6kV in steps of 1 kV. 

 

10 shots per combination. 

 One 

shot 

per 

minute. 

 

Serial impedance: 2 Ohm for Europe, 12Ohm for Nafta 

 

Polarity and phase: Positive (phase 90º) & Negative (phase 270º) 

 
Reference: IEC61000-4-5 and for USA: 3135 019 8029 Reliability evaluation. 
 
Requirements: 

 

Apparatus should fulfil the leakage current requirements of IEC60065 point 9.1.1 (UAN-D1631) 

 

Defects or permanent deviations are not allowed. 

 

 

3.1.3 Mains 

Drop-out 

Immunity 

 
The product shall withstand mains failures of: 

 

Variation 0% (=100% dip) at T-event = 50 mSec. Performance criterion B 

 

Variation 40% (=60% dip) at T-event = 100 mSec. Performance criterion B 

 

Variation 0% (=100% dip) at T-event = 5 Sec. Performance criterion C 

 
Additional for USA apparatus: See 3135 019 8029 Reliability evaluation. 

 

Variation 0% (=100% dip) at T-event = 100 mSec in standby mode. Performance criterion B 

 

Requirement: 
 
No misoperation and no interference of user in order to guarantee continuation of performed function. 
Reference: IEC61000-4-11 For measuring method refer to UAN-D1724, as far as applicable. 
Performance criterions according to IEC61000-4-4 Amendment 1 
Performance Requirement 
Criterion A - No any degradation of specification. 
Criterion B - Temporary degradation / self recoverable. 
Criterion C - No damage, resolvable hang-up. 
Criterion D - Not recoverable loss of function. 
 

Summary of Contents for MCM1055/51/98






































Reviews: