26
English
Timer Setting
The system can switch on to CD, TUNER, or
TAPE mode automatically at a preset time,
serving as an alarm to wake you up.
IMPORTANT!
– Before setting the timer, ensure that the
clock is set correctly.
– The timer will always be switched on
after it has been set.
– The timer will not start if a recording is in
progress.
– The volume of the timer will increase
gradually from the minimum level to the
last tuned volume level.
1
Press and hold
TIMER
on the remote control
for more than
two seconds
.
➜
"
AM 12:00
" or "
00:00
" or the last timer
setting will start flashing.
➜
TIMER
will start flashing.
➜
The selected source will be lighted while
other available sources are flashing.
2
Press
CD 1•2•3
,
TUNER
or
TAPE
to select
the desired source.
●
Before setting the timer, make sure the music
source has been prepared.
CD 1•2•3
– Load the disc(s). To start from a
specific track, make a programme (refer to “CD
Operation - Programming the disc tracks”).
TUNER
– tune to the desired radio station.
TAPE
– load a prerecorded tape.
3
Press
à
or
á
repeatedly to set the hour for
the timer to start.
4
Press
í
or
ë
repeatedly to set the minute for
the timer to start.
5
Press
TIMER
to store the start time.
➜
"
TIMER ON
" will be displayed and followed
by the set timer "
XX:XX
" and then the selected
source.
➜
TIMER
will remain on the display.
●
At the preset time, the selected source will play.
To exit without storing the setting
●
Press
Ç
on the system.
Notes:
– If CD is the selected source and it is not
available when the preset time is reached, Tuner
will be selected automatically.
– During timer setting, if no key is pressed within
90 seconds, the system will exit timer setting mode
automatically.
To check the TIMER
●
Press
TIMER
on the remote control.
➜
If the timer has been activated, the set timer
information will be displayed.
➜
If the timer has been deactivated, "
OFF
" will
be displayed.
To activate/deactivate the TIMER
●
Press
TIMER ON/OFF
repeatedly on the
remote control.
➜
If activated, the last set timer information will
be shown for a few seconds and
TIMER
will
appear on the display.
➜
If deactivated, “
OFF
” will be displayed.
Sleep Timer Setting
The sleep timer enables the system to switch to
Standby mode automatically within a preset
amount of time.
1
Press
SLEEP
on the remote control repeatedly
to select a preset amount of time.
➜
The selections are as follows (time in
minutes):
15
™
30
™
45
™
60
™
OFF
™
15
…
➜
"
SLEEP XX
" or "
OFF
" will be displayed.
"
XX
" is the time in minutes.
2
When you reach the desired length of time, stop
pressing the
SLEEP
button.
➜
SLEEP
will appear on the display, except for
"
OFF
" mode.
➜
The Sleep Timer is now set. Before the
system switches to standby mode, a countdown
of 10 seconds will be displayed.
"
SLEEP 10
"
™
"
SLEEP 9
"....
™
"
SLEEP 1
"
™
"
SLEEP
"
While SLEEP mode is activated
To check the remaining length of time
●
Press
SLEEP
once
.
To change the preset sleep timer
●
Press
SLEEP
twice
.
➜
The display will show the remaining time
followed by the sequence of sleep timer options.
To deactivate the Sleep Timer
●
Press
SLEEP
repeatedly until "
OFF
" is
displayed, or press the
STANDBY ON
button.
Clock / Timer