1.2
4
INSTALLATION
Attention:
Installation should be performed by
qualified service personnel only in accordance with
the National Electrical Code or applicable local
codes.
4.1
Removing Module From Carton
Refer to
ILLUSTRATIONS
for component description.
CAUTION:
Keep in carton until ready to install
in backbox. Be sure to observe all safety measures
for static control when working with this unit
while out of its enclosure. Otherwise, static
damage may result.
For removal from carton and installation instructions, see
LTC 0809 Series Camera Module Installation
under
INSTALLATION
in the
Instructions for Use
supplied with
the applicable
LTC 7460 Series Ceiling Mount
ordered.
CAUTION:
Do not handle the unit by the circuit
board because this may result in physical damage
to the unit.
5
OPERATION
5.1
Camera Control
These units, as shipped, are factory adjusted as described below:
•
Line-lock mode enabled with zero degree phase delay.
•
AGC on.
•
Backlight compensation off.
•
Electronic shutter off.
•
Automatic white balance on.
5.2
Changing Operating Modes
The AutoDome unit operating modes can be changed using
either a TC8135B Series Controller/Follower or an Allegiant®
series keyboard. An Allegiant series keyboard is required to take
full advantage of all the various features available. See
AutoDome Commands
for description of various operating
adjustments.
5.3
AutoDome Commands
PAN & TILT - COMMANDS USING AUXILIARY CONTROLS
LENS - COMMANDS USING AUXILIARY CONTROLS
CAMERA - COMMANDS USING AUXILIARY CONTROLS
Receiver/Driver
Aux
Description
On/Off
Notes
Function
No.
Scan
1
Auto-pan without On/off
5, 8
limits
Auto-Pan
2
Auto-pan between On/off
8
limits
Pre-Position
8
--
On/off
8
Tour
Return Home
9
return to home
On/off
2, 7
upon inactivity
Set Scan/auto-
pan speed
14
--
Inc/dec
2, 7
Set tour period
15
Sets pause
Inc/dec
2, 7
between tour
callups
Auto-Speed
16
Enables/disables
On/off
2, 7
auto-speed
Auto-Pivot
18
Enables/disables
On/off
2, 7
Enable
auto-pivot
Field of View
45
---
On/off
2, 7
Optimize
Lens Function
Aux No. Description
On/Off
Notes
Iris Control
3
--
Auto/
1, 9
manual
Focus Control
4
--
Auto/
1, 9
manual
Auto-iris ALC adj
10
--
Peak/ave
1, 7
Auto-iris Level adj 11
--
Inc/dec
1, 7
Auto-focus
12
Activates AF
On/off
2
Activation
upon movement
Auto-iris Activation 13
Activates AI
On/off
2
upon movement
Spot Focus
17
Activates Spot
On/off
2, 7
Camera
Aux No.
On/Off
Notes
Function
Backlight
20
On/off
1, 10
Compensation
Shutter
23
On/off
1, 7
Auto shutter
24
On/off
2, 7
activation
White Balance
30
Auto/
7
manual
Red Adjust
31
Inc/dec
1, 7
Blue Adjust
32
Inc/dec
1, 7
R-Y Hue Adjust
33
Inc/dec
3, 7
B-Y Hue Adjust
34
Inc/dec
3, 7
Fixed White
35
Indoor/
Balance
outdoor
1, 7
Factory Default
40
Set/---
1,3, 7
Settings
Adjust LL Phase 41
Inc/dec
3, 7
Delay
Sync Mode
42
ll/xtal
3, 7
AGC
43
On/off
3
Vertical Aperture
Adjust
44
Inc/dec
7
